Publicidad
Idiomas disponibles
Idiomas disponibles
• Unscrew the protective cap of the RESET button.
GB
• Press the RESET button of the Hi-limiter (thermal cut-out).
You should hear a click sound.
• Screw back the protective cap on the RESET button.
• Connect to the power supply and you can use it again.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the elec-
trical mains and cool down before storage, cleaning & main-
tenance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• No parts are dishwasher safe.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
• For item 215029: Special care must be taken when moving
or transporting the machine due to its heavy weight. With
at least 2 persons or using a cart. Move the machine slowly,
carefully, and never incline more than 45°.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
8
Problems
Possible cause
The appliance does
• Power plug is
not switch ON.
not connected
properly with the
electrical outlet.
• On/OFF (1) button
is not pressed.
Cooling fan is
• This is normal.
operating even
The cooling fan
after the appliance
continues running
is switched to OFF
in OFF mode for
mode.
some time to cool
down all internal
elements.
Error code identification
Error
Possible cause
codes
E01
The internal tempera-
ture of the appliance is
too high. Buzzer alarm
sound is heard.
E02
The appliance is
overheated and buzzer
alarm sound is heard.
E03
Input supply voltage is
too high (>265v).
E04
Input supply voltage is
too low (<135v).
E05
Oil temperature sensor
short / open circuit.
E06
Coil temperature sensor
short circuit.
E07
Coil temperature sensor
open circuit.
E08
Coil temperature sensor
over heat.
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
Discarding & Environment
When decommissioning the appliance, the prod-
uct must not be disposed of with other household
waste. Instead, it is your responsibility to dispose
to your waste equipment by handing it over to a
designated collection point. Failure to follow this
rule may be penalized in accordance with applicable regula-
Possible solution
• Check the power
plug to make sure
it is connected
properly.
• Press the On/OFF
(1) button to start
operation.
• Wait until the
cooling fan stops
rotating.
Possible solution
Press ON / OFF (1)
button to switch OFF the
appliance and unplug the
appliance, wait until the
appliance is completely
cool down. Also RESET
the Hi-limiter.
Make sure that the
appliance is connected to
a suitable electrical power
supply.
Please contact your
supplier.
Publicidad
