Kyocera AG1009 Manual Del Usuario página 7

Additional Safety Warnings Specific for Abrasive Cutting-Off
Operations:
a) Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth
of cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut
and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your body, the possible kickback
may propel the spinning wheel and the power tool directly
at you.
c) When wheel is binding or when interrupting a cut
for any reason, switch off the power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the cut-
off wheel from the cut while the wheel is in motion
otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully reenter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
f) Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding
wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
Safety Warnings Specific for Sanding Operations:
a) Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding paper
extending beyond the sanding pad presents a laceration
hazard and may cause snagging, tearing of the disc or
kickback.
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the voltage
marked on the rating plate.
2. Never use the tool if its cover or any bolts are missing. If
the cover or bolts have been removed, replace them prior
to use. Maintain all parts in good working order.
3. Never touch the blade, drill bit, grinding wheel or other
moving parts during use.
4. Never start a tool when its rotating component is in con-
tact with the work piece.
5. Grinding wheels must be stored in a dry place.
Do not put any object on the wheels.
Grinding wheels must not be used for any operation other
than grinding.
Grinding wheels must be stored and handled with care in
accordance with the manufacturer's instruction.
6. Ensure that the wheel is fitted in accordance with this
manual.
7. Ensure that the grinding wheel is correctly mounted and
tightened before use and run the tool at no-load speed for
30 seconds in a safe position. Stop immediately if there
is considerable vibration or if other defects are detected.
If this condition occurs, check the tool to determine the
cause.
8. Check that the work piece is properly supported.
9. Do not remove the soft paper in the center of the grinding
wheel. (If the paper has been previously removed, insert
some soft paper or rubber between grinding wheel and
flange.)
10. Grip the tool securely with both hands while operating.
DESCRIPTION
1. Grinding Wheel (Optional)
2. Wheel guard
3. Switch
4. Spindle shaft
5. Disc flange
6. Clamp nut
7. Lock button
8. Wrench
9. Auxiliary handle
10. Sanding pad 100mm (Optional)
11. Sanding pad 110mm (Optional)
12. Sanding disc 100mm (Optional)
13. Sanding disc 115mm (Optional not available-purchase
aftermarket)
14. Clamp nut for sanding disc M10 (Optional)
15. Clamp nut for sanding disc M14 (Optional)
16. Wheel guard for cutting-off(Optional) (Except for AG1259)
17. Cutting-off wheel (Optional) (Except for AG1259)
18. Screw
19. Antidust filter
SPECIFICATIONS
Capacities
Grinding wheel
Sanding disc
Cutting-off wheel
Input
Spindle thread
Rated speed
Overall length
Net weight
Capacities
Grinding wheel
Sanding disc
Cutting-off wheel
Input
Spindle thread
Rated speed
Overall length
Net weight
Capacities
Grinding wheel
Sanding disc
Input
Spindle thread
Rated speed
Overall length
Net weight
- 6 -
AG1009
100 mm (4") x 6mm
100 mm (4")
100 mm (4")
1,010 W
M10
-1
11,000 min
268 mm (10-35/64")
1.7 kg (3.7 lbs.)
AG1159
115 mm (4-1/2") x 6mm
115 mm (4-1/2")
115 mm (4-1/2")
1,010 W
M14
-1
11,000 min
268 mm (10-35/64")
1.8 kg (3.9 lbs)
AG1259
125 mm (5") x 6mm
115 mm (4-1/2")
1,010 W
M14
-1
11,000 min
268 mm (10-35/64")
1.9 kg (4.1 lbs)