Kyocera AG1009 Manual Del Usuario página 8

ASG1009
Capacities
Grinding wheel 100 mm (4") x 6mm
Sanding disc 100 mm (4")
Cutting-off wheel 100 mm (4")
Input 750 W
Spindle thread M10
Rated speed 11,000 min
Overall length 268 mm (10-35/64")
Net weight 1.6 kg (3.5 lbs)
ASG1159
Capacities
Grinding wheel 115 mm (4-1/2") x 6mm
Sanding disc 115 mm (4-1/2")
Cutting-off wheel 115 mm (4-1/2")
Input 750 W
Spindle thread M14
Rated speed 11,000 min
Overall length 268 mm (10-35/64")
Net weight 1.7 kg (3.7 lbs.)
* Be sure to check the nameplate on the product, because
the voltage is subject to change depending on the area in
which the product is to be used.
Do not use wheels having a Maximum permissible circumfer-
ential speed below 4,800 m/min.
(Example of calculation)
3,454 = 3.14 x 100 x 11,000 / 1,000
3,454 : circumferential speed of grinding wheel
100 : Wheel diameter
11,000 : Rated speed of grinder
STANDARD ACCESSORIES
Wrench, Auxiliary handle
APPLICATIONS
(Use only for the purposes listed below.)
1. Grinding and finishing for welds.
2. Deburring and finishing iron, bronze, aluminum, and other
metal castings.
3. Surface finishing with sanding disc.
4. Cutting-off and grooving metal. (Except for AG1259)
(With a cutting-off wheel for metal)
5. Cutting-off and grooving nonmetal. (Except for AG1259)
(With a cutting-off wheel for nonmetal)
SWITCH (Fig.1)
This tool is started and stopped by sliding and releasing the switch(3).
For the convenience for continuous operation, press the rear end
down, then slide the switch along and press the front end down
to lock it (action A).
To release the lock, press the rear end of the switch (action B).
INSTALLATION OF GRINDING WHEEL (Fig.2,3)
WARNING!
Use only grinding wheels having a maximum operating speed
at least as high as peripheral speed 80 m/sec.(4,800 m/min.)
marked on them.
GRINDING WHEEL
1. Attach the disc flange (5) , grinding wheel (1) and clamp
nut (6) to the spindle shaft (4).
-1
-1
Be sure that the disc flange is properly seated on the
spindle shaft.
2. Depress the lock button (7) located on the right side of
gear case.
3. Using the wrench (8) provided, tighten the clamp nut
(clockwise).
CAUTION!
Do not tighten excessively since this can cause cracks in
the grinding wheel.
CAUTION!
When using grinding wheels or cut-off wheel (17) which are
less than 3.5mm thick, the clamp nut should be set reversely
as shown in fig 4.
WARNING!
Check carefully whether or not there are cracks in the wheel.
Replace a cracked wheel immediately.
INSTALLATION OF SANDING DISC (Fig.2,3)
1. Attach the disc flange (5) for only AG1009 and ASG1009,
sanding pad (10,11), sanding disc (12,13) and clamp nut
for sanding disc (14,15) to the spindle shaft (4).
Be sure that the disc flange is properly seated on the
spindle shaft.
2. Depress the lock button (7) located on the right side of
gear case.
3. Using the wrench (8) provided, tighten the clamp nut for
sanding disc (clockwise).
AUXILIARY HANDLE (Fig.5)
The auxiliary handle (9) can be attached to either side of the
gear case.
OPERATING
KEEP SAFETY GUARDS IN PLACE.
NEVER COVER AIR VENTS SINCE THEY MUST ALWAYS BE
OPEN FOR PROPER MOTOR COOLING.
GRINDING AND SANDING (Fig.6)
The key to efficient operating is controlling the pressure and
surface contact between the disc and work piece. Flat surfaces
are ground at an acute angle, usually 15 to 30 degrees with the
work piece. Allow the disc to reach full speed before starting to
grind. Too great an angle causes concentration of pressure on a
small area which may gouge or burn the work surface.
CUTTING-OFF
1. Replace the grinding wheel with the cutting-off wheel.
2. Loosen the screw(18) and replace the wheel guard (2) with
the wheel guard for cutting-off (16).
Then, clamp the wheel guard for cutting-off by tightening
the screw (18).
3. Attach the aux. handle to either side of the gear case.
Align the wheel to the material to be cut and lower it slowly.
Move the tool without applying excess pressure. (If excess
pressure is applied, it will tend to jam the wheel causing a rough
cut.)
MAINTENANCE
After use, check the tool to make sure that it is in top condition.
It is recommended that you take this tool to an Authorized Ser-
vice Center for a thorough cleaning and lubrication at least once
per year.
DO NOT MAKE ANY ADJUSTMENTS WHILE THE MOTOR IS
IN MOTION.
ALWAYS DISCONNECT THE POWER CORD FROM THE RE-
CEPTACLE BEFORE CHANGING REMOVABLE OR EXPEND-
- 7 -