Forever light RTV0700001 Manual De Instrucciones página 8

1. INTRODUCTION
BG
In the interest of your safety, we recommend that you read these operating instructions carefully. This manual is intended to familiarize the user with the operation
of the device. No part of this manual may be reproduced, distributed, translated, or transmitted in any form or by any electronic or mechanical means, including
CZ
photocopying, recording, or storage on any information storage or sharing system without the prior written consent of the manufacturer. All other trademarks and
copyrights are the property of their respective owners. Specifications and colors may slightly differ from the product shown in the pictures.
DE
Light source intended for use in outdoor or industrial applications.
EE
2. SAFETY OF USE
• We recommend that a qualified person install the product.
EN
• Please read the instructions in the manual carefully. Failure to follow these instructions may be dangerous or illegal.
• During installation or maintenance, remember to always turn off the electricity supply!
ES • The chosen mounting location should allow for safe installation and connection to the power source.
• Place the lamp out of the reach of children and unauthorized persons.
• Always follow basic safety precautions when using it in order to reduce the risk of fire and electric shock.
FI
• Do not look directly at the light source as there is a risk of eye damage.
• The product cannot be modified, any modifications may make the product dangerous.
FR
• Repairs must only be carried out by qualified technicians using original spare parts. Failure to do so may be very dangerous for the user. In this case, contact
the manufacturer's service department.
• Never open the floodlight housing. There is a risk of electric shock if the casing is opened.
GR
• If there is smoke coming from the floodlight, hear unusual sounds or smell unusual odors, switch the device off immediately. Do not turn it on again, but
contact a qualified service center.
HR
• If the floodlight has a broken or broken glass, immediately disconnect it from the power supply and dismantle it! Damage to the glass pane qualifies
the floodlight for disposal.
• Avoid contact of the device with liquids, as they may damage the electronic parts of the device. Avoid very high temperatures; they can shorten the life of
HU
electronic device components or melt plastic parts.
• Only use a dry and soft cloth to clean the device. Do not use agents with a high concentration of acid or alkaline.
IT
• Environment safety, do not use the device in places where its use is forbidden or where it may be dangerous.
LT 3. PRODUCT DESCRIPTION (Fig. 1)
1. ADC12 Die-casting housing
2. Reflector
LV
3. Bracket
4. Glass
NL
5. Self-tapping screws
6. Mechanical screws
NO 7. Flat washer
8. Spring cushion
9. Waterproof connector
PL
10. Waterproof valve
11. PCB board with electronic components
PT
4. INSTALLATION
RO The floodlight should be installed by an authorized and experienced electrician. Before starting the installation, it is necessary to turn off the power supply
to which the floodlight is to be connected!
The floodlight holder has mounting holes with a diameter of 7mm.
RU
To facilitate the assembly, unscrew the handle from the floodlight by removing the screws on both sides (Fig. 2)
Screw the holder to the base and then screw the floodlight back to the holder, remembering about the order of the washers.
SE
The electric wires must be connected in accordance with the presented instructions: Connect the power wires to the mains to a terminal block or a sealed connector,
as appropriate: brown wire: Line, blue wire: Neutral, yellow-green – Protective
SK
5. TROUBLE SHOOTING
In case of any problems with the device, please read the tips below.
SL
The lamp does not light even though it is connected:
• Disconnect the lamp from the power source.
SR
• Check if the power source connected to the lamp is not damaged.
• In case of using an extension cord, check if it is connected
• Check that the cable is properly connected at the connector connection stage.
UA
If you are not sure, do not perform repairs yourself, contact the manufacturer's service.
In case of disturbing symptoms, such as blinking, sparks or smoke, disconnect the lamp from the power source immediately. Do not try to repair it yourself, contact
the manufacturer's service.
WARNING:
The manufacturer is not responsible for the consequences of the situations caused improper use of the device or non-compliance with the recommendations.
6. CORRECT DISPOSAL OF USED EQUIPMENT
The device is marked with the symbol of a crossed-out garbage container, in accordance with the European Directive 2012/19 / EU on used equipment electrical
and electronic equipment (Waste Electrical and Electronic Equipment - WEEE). Products marked with this symbol after the period has expired should not be
utilized or disposed of with other wastes from the household. The user is obliged to get rid of used electrical and electronic equipment by delivering it to a
designated point where such hazardous waste is subjected to the recycling process. Collecting this type of waste in dedicated places and the proper process of their
recovery contribute to the protection of natural resources. Proper recycling of used electrical and electronic equipment has a positive effect on health and the
environment human. For information on where and how to dispose of used electrical and electronic equipment in an environmentally safe way, the user should
contact the appropriate local government authority, the waste collection point or the point of sale where the equipment was purchased.
7. DECLARATION OF COMPLIANCE WITH EUROPEAN UNION DIRECTIVES
TelForceOne S.A. hereby declares that the Aspire LED Floodlight device complies with the basic requirements and other provisions of the Directives, the so-
called The „new approach" of the European Union.
The full text of the EU declaration of conformity is available at the following internet address: www.foreverlight.eu under „DOWNLOAD".
(Fig. 3.).