Descargar Imprimir esta página

Krups BW923810 Manual De Instrucciones página 5

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 18
2
Wait for 3 seconds until the temperature is confirmed.
After 3 seconds, the temperature selection button
solid light to blinking mode and the kettle starts heating.
3
To stop heating, press the On/Off button
• The temperature selection button
• The temperature setting can be changed by pressing the temperature
selection button
even during heating.
• When the set temperature is lower than the current water temperature, it will
not be heated.
• Immediately before the water reaches the set temperature, you will hear
three short beep sounds that notify you that the water will soon reach the set
temperature. When the water reaches to the set temperature, you will hear a
prolonged beep sound and the kettle will stop heating.
• The heating time will differ to some extent depending on the volume and
temperature of the water or the room temperature.
Direct boil mode – Boil the water directly to 100°C
1
Press the one touch boiling button
immediately to 100°C after 3 seconds.
2
To stop heating, press the On/Off button
button
• The one touch boiling button
will blink during heating.
• Immediately before the water reaches the set temperature, you will hear
three short beep sounds that notify you that the water will soon reach the set
temperature. When the water reaches the set temperature, you will hear a
prolonged beep sound and the kettle will stop heating.
• The heating time will differ to some extent depending on the volume and
temperature of the water or the room temperature.
Keep warm mode – Keep warm the water at desired temperature
Mode 1:
1
Press the temperature selection button
button
to select the desired temperature and press the keep warm button
The kettle will first heat up to the selected temperature and then keep warm
for 30 minutes.
2
To stop the keep warm function, press the keep warm button
heating process will continue.
will change from
.
will blink during heating.
, the kettle will start heating
or the one touch boiling
or press the one touch boiling
, the
6
3
To stop heating and keep warm function, press the On/Off button
Mode 2:
1
The kettle will keep warm at the previous set temperature.
2
To stop the keep warm function, press the keep warm button
button
.
• The temperature selection button
during heating phase and the keep warm button
warm phase.
• The keep-warm time is 30 minutes.
• For the heating phase, immediately before the water reaches the set temperature,
you will hear three short beep sounds that notify you that the water will soon reach
the set temperature. When the water reaches to the set temperature, you will hear
a prolonged beep sound and the kettle will stop heating.
• For the keep warm mode, there will be a prolonged beep sound after the
30 minutes keep-warm
• The maximum keep-warm temperature is 95°C. If it is set to 100°C, it will
heat to 100°C and keep warm at 95°C.
• When the set temperature is lower than the current water temperature, it will
not be heated but keep warm function will be activated.
• If you press the keep-warm button when the temperature is not set, the
kettle will heat and keep warm to 60°C.
• Even if you remove the kettle from the power base during keep-warm, keep-
warm will be resumed by placing the kettle on the power base again and
pressing the keep-warm button within 10 seconds.
RECOMMENDED TEMPERATURES
40°C: water to prepare baby milk
60°C: water to prepare lemon water
70°C : water to prepare white tea
80°C : water to prepare green tea
90°C : water to prepare freshly ground coffee
100°C : boiling water/infusions
.
6. THE KETTLE WILL SWITCH OFF AUTOMATICALLY
As soon as the program is finished.
• Do not leave water in the kettle after use as this quickens the formation of
scale.
.
or On/Off
and the keep-warm button
will blink
will blink during keeping
7
EN

Publicidad

loading