Publicidad
Idiomas disponibles
Idiomas disponibles
F ) WHEN FEEDING MATERIAL INTO THE MACHINE BE EXTREMELY CAREFUL
THAT PIECES OF METAL, ROCKS, BOTTLES, CANS OR OTHER FOREIGN OBJECTS
ARE NOT INCLUDED.
G ) IF THE CUTTING MECHANISM STRIKES ANY FOREIGN OBJECTS OR IF THE
MACHINE SHOULD START MAKING ANY UNUSUAL NOISE OR VIBRATION,
IMMEDIATELY SHUT OFF THE POWER SOURCE AND ALLOW THE MACHINE
TO STOP. DISCONNECT THE MACHINE FROM THE SUPPLY AND TAKE THE
FOLLOWING STEPS BEFORE RESTARTING AND OPERATING THE MACHINE:
I) INSPECT FOR DAMAGE;
II) REPLACE OR REPAIR ANY DAMAGED PARTS;
III) CHECK FOR AND TIGHTEN ANY LOOSE PARTS.
H ) DO NOT ALLOW PROCESSED MATERIAL TO BUILD UP IN THE DISCHARGE
ZONE; THIS MAY PREVENT PROPER DISCHARGE AND CAN RESULT IN KICKBACK
OF MATERIAL THROUGH THE INTAKE OPENING.
I ) IF THE MACHINE BECOMES CLOGGED, SHUT-OFF THE POWER SOURCE AND
DISCONNECT THE MACHINE FROM SUPPLY BEFORE CLEANING DEBRIS.
J ) NEVER OPERATE THE MACHINE WITH DEFECTIVE GUARDS OR SHIELDS, OR
WITHOUT SAFETY DEVICES, FOR EXAMPLE DEBRIS COLLECTOR IN PLACE.
K ) KEEP THE POWER SOURCE CLEAN OF DEBRIS AND OTHER ACCUMULATIONS
TO PREVENT DAMAGE TO THE POWER SOURCE OR POSSIBLE FIRE.
L ) DO NOT TRANSPORT THIS MACHINE WHILE THE POWER SOURCE IS
RUNNING.
M ) STOP THE MACHINE, AND REMOVE PLUG FROM THE SOCKET. MAKE SURE
THAT ALL MOVING PARTS HAVE COME TO A COMPLETE STOP
- WHENEVER YOU LEAVE THE MACHINE,
- BEFORE CLEARING BLOCKAGES OR UNCLOGGING CHUTE,
- BEFORE CHECKING, CLEANING OR WORKING ON THE MACHINE.
N ) DO NOT TILT THE MACHINE WHILE THE POWER SOURCE IS RUNNING.
2.10 RESIDUAL RISKS
• EVEN IF YOU ARE OPERATING THIS PRODUCT IN ACCORDANCE WITH ALL
THE SAFETY REQUIREMENTS, POTENTIAL RISKS OF INJURY AND DAMAGE
REMAIN. THE FOLLOWING DANGERS CAN ARISE IN CONNECTION WITH THE
STRUCTURE AND DESIGN OF THIS PRODUCT:
4MAINTENANCE AND STORAGE
A ) WHEN THE MACHINE IS STOPPED FOR SERVICING, INSPECTION, OR
STORAGE, OR TO CHANGE AN ACCESSORY, SHUT OFF THE POWER SOURCE,
DISCONNECT THE MACHINE FROM THE SUPPLY AND MAKE SURE THAT ALL
MOVING PARTS ARE COME TO A COMPLETE STOP. ALLOW THE MACHINE TO
COOL BEFORE MAKING ANY INSPECTIONS, ADJUSTMENTS, ETC. MAINTAIN
THE MACHINE WITH CARE AND KEEP IT CLEAN.
B ) STORE THE MACHINE IN A DRY PLACE OUT OF THE REACH OF CHILDREN.
C ) ALWAYS ALLOW THE MACHINE TO COOL BEFORE STORING.
D ) WHEN SERVICING THE SHREDDING MEANS BE AWARE THAT, EVEN
THOUGH THE POWER SOURCE IS SWITCHED OFF DUE TO THE INTERLOCK
FEATURE OF THE GUARD, THE SHREDDING MEANS CAN STILL BE MOVED.
E ) REPLACE WORN OR DAMAGED PARTS FOR SAFETY. USE ONLY GENUINE
REPLACEMENT PARTS AND ACCESSORISES.
F ) NEVER ATTEMPT TO OVERRIDE THE INTERLOCKED FEATURE OF THE GUARD.
5ADDITIONAL SAFETY INSTRUCTIONS FOR UNITS WITH
BAGGING ATTACHMENTS
• SWITCH-OFF THE MACHINE BEFORE ATTACHING OR REMOVING THE BAG.
6RECOMMENDATION
• THE MACHINE SHOULD BE SUPPLIED VIA A RESIDUAL CURRENT DEVICE
(RCD) WITH A TRIPPING CURRENT OF NOT MORE THAN 30 MA. AVOID USING
THE MACHINE IN BAD WEATHER CONDITIONS ESPECIALLY WHEN THERE IS A
RISK OF LIGHTNING.
• DO NOT USE EXTENSION CORDS LIGHTER THAN:
-IF RUBBER INSULATED, ORDINARY TOUGH RUBBER SHEATHED FLEXIBLE
CORD (CODE DESIGNATION 60245 LEC 53; H05 RN-F);
-IF POLYVINYL CHLORIDE INSULATED, ORDINARY POLYVINYL CHLORIDE
SHEATHED FLEXIBLE CORD (CODE DESIGNATION 60227 LEC 53; H05 VV-F)
• 1.HEALTH DEFECTS RESULTING FROM VIBRATION EMISSION IF THE
PRODUCT IS BEING USED OVER LONG PERIODS OF TIME OR NOT ADEQUATELY
MANAGED AND PROPERLY MAINTAINED.
• 2.INJURIES AND DAMAGE TO PROPERTY DUE TO BROKEN APPLICATION
TOOLS OR THE SUDDEN IMPACT OF HIDDEN OBJECTS DURING USE.
• 3.DANGER OF INJURY AND PROPERTY DAMAGE CAUSED BY FLYING OBJECTS
177
FR
ES
PT
IT
EL
PL
RU
KZ
UA
RO
EN
Publicidad
