Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INTERFACE FEATURES
• Designed for B&O A2B amplifiers
• A2B data interface w/AXDSP-X (digital signal processor) built-in
• Includes an amplifier bypass harness
• Retains factory chimes including parking sensor chimes
• Retains SYNC voice prompts
• Chimes and voice prompts go through the aftermarket amplifier and/
or cluster
• Selectable 31 Band graphic EQ or 5 Band Parametric EQ
• 10 individually assignable outputs
For Dash Disassembly Instructions, refer
to metraonline.com.
AxxessInterfaces.com
Ford Select Models 2017-UP A2B Data Inter-
face with Amplifier Bypass Harness & DSP
Visit axxessinterfaces.com for current application list.
INTERFACE COMPONENTS
• AXDSPX-A2B2 interface
• AXDSPX-A2B2 harness
• AXDSPX-A2B2 interface
harness (male connectors:
12-pin, 16-pin)
• Independent equalization on each of the 10 outputs
• Independent high pass, low pass, and bandpass filters
• Each channel can be delayed independently up to 10ms
• Clipping detection and limiting circuits
• Settings adjusted via Bluetooth® in a smart device application (tablet
or mobile phone), compatible with both Android and Apple devices
• Read, write, and store configurations for future recall
• Password protect feature available in the mobile app
• Micro-B USB updatable
Enter the year, make, and model of the vehicle in the Vehicle Fit Guide for Radio Install kits.
© COPYRIGHT 2023 METRA ELECTRONICS CORPORATION
AXDSPX-A2B2
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................3
Troubleshooting .....................................................4
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
• Amplifier bypass harness
solder, and heat shrink • Tape • Wire cutter
(female connectors: 8-pin
• Zip ties
black, 20-pin gray)
Google Play Store
• AXBK-1
• A2B-EXT
ATTENTION:
ignition, disconnect the negative battery
terminal before installing this product. Ensure
that all installation connections, especially the
air bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
Apple App Store
iOS 12.1 or higher
With the key out of the
REV. 2/7/23 INSTAXDSPX-A2B2

Publicidad

loading

Resumen de contenidos para Axxess AXDSPX-A2B2

  • Página 1 Visit axxessinterfaces.com for current application list. Troubleshooting .............4 TOOLS REQUIRED INTERFACE COMPONENTS • Crimping tool and connectors, or solder gun, • AXDSPX-A2B2 interface • Amplifier bypass harness solder, and heat shrink • Tape • Wire cutter • AXDSPX-A2B2 harness (female connectors: 8-pin • Zip ties Apple App Store •...
  • Página 2 CONNECTIONS Factory Amp Harness RCA Jacks (sold separately) Gray - Front Right + Purple - Rear Right + Gray/Black - Front Right - Purple/Black - Rear Right - White - Front Left + Green - Rear Left + White/Black - Front Left - Green/Black - Rear Left - Brown/White * - Center + Dark Blue/Pink * - Center -...
  • Página 3 7. Connect the amp turn-on wire from the AXDSPX-A2B2 harness. 8. Click the Identify button to confirm that the AXDSPX-A2B2 is connected properly. If so, a chime will be heard from the front left speaker or gauge cluster. Test all functions of the installation for proper operation.
  • Página 4 Contact our Tech Support line at: 386-257-1187 • If the Red light in the AXDSPX-A2B2 interface is blinking, it is not communicating with the vehicle. Remove the key from the Or via email at: ignition, unplug the connectors from the interface, then inspect all connections made. If everything is proper, connect the techsupport@metra-autosound.com...
  • Página 5 • Herramienta de prensado y conectores o pistola soldadora, soplete y tubo termoretráctil •Cinta COMPONENTES DE LA INTERFAZ •Cortador de cables •Abrazaderas de plástico • Interfaz AXDSPX-A2B2 • Arnés de derivación de • Arnés AXDSPX-A2B2 amplificador (conectores Apple App Store • Arnés de interfaz AXDSPX-A2B3...
  • Página 6 CONEXIONES Arnés de Amplificador de Fábrica Conectores RCA (se venden por separado) Gris: Delantero derecho + Morado: Trasero derecho + Gris con negro: Delantero derecho - Morado con negro: Trasero derecho - Blanco: Delantero izquierdo + Verde: Trasero izquierdo + Blanco con negro: Delantero izquierdo - Verde con negro: Trasero izquierdo - Café...
  • Página 7 7. Conecte el cable de encendido del amplificador que está en el arnés AXDSPX-A2B2. 8. Haga clic en el botón “Identificar” para confirmar que el AXDSPX-A2B2 esté conectado correctamente. Si lo está, se escuchará un tono en la bocina delantera izquierda o el tablero de instrumentos. Pruebe todas las funciones de la instalación para confirmar que funcionen correctamente.
  • Página 8 Póngase en contacto con nuestra línea de soporte técnico en: • Si parpadea la luz roja en la interfaz AXDSPX-A2B2, eso quiere decir que no se está comunicando con el vehículo. Quite la 386-257-1187 llave de la marcha, desconecte los conectores de la interfaz y proceda a revisar todas las conexiones que se realizaron. Si O por correo electrónico a:...