Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

INTERFACE FEATURES
• Designed for Revel A2B amplifiers
• A2B data interface w/AXDSP-X (digital signal processor) built-in
• Includes an amplifier bypass harness
• Retains factory chimes including parking sensor chimes
• Retains voice prompts
• Chimes and voice prompts go through the aftermarket amplifier and/
or cluster
• Selectable 31 Band graphic EQ or 5 Band Parametric EQ
• 10 individually assignable outputs
For Dash Disassembly Instructions, refer
to metraonline.com.
AxxessInterfaces.com
Lincoln Select Models 2018-Up A2B Data
Interface w/Amplifier Bypass Harness & DSP
Visit axxessinterfaces.com for current application list.
INTERFACE COMPONENTS
• AXDSPX-A2B3 interface
• AXDSPX-A2B3 harness
• LD-DSP-A2B-3
• LD-DSP-A2B-4
• AXDSPX-A2B3 interface harness
(male connectors: 12-pin, 16-pin)
• Independent equalization on each of the 10 outputs
• Independent high pass, low pass, and bandpass filters
• Each channel can be delayed independently up to 10ms
• Clipping detection and limiting circuits
• Settings adjusted via Bluetooth® in a smart device application (tablet
or mobile phone), compatible with both Android and Apple devices
• Read, write, and store configurations for future recall
• Password protect feature available in the mobile app
• Micro-B USB updatable
Enter the year, make, and model of the vehicle in the Vehicle Fit Guide for Radio Install kits.
© COPYRIGHT 2023 METRA ELECTRONICS CORPORATION
AXDSPX-A2B3
• Amplifier bypass harness
(female connectors: 12-pin black,
20-pin gray)
• AXBK-1
• A2B-EXT
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Connections ............................................................2
Installation .............................................................3
Troubleshooting .....................................................4
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
• Zip ties
Apple App Store
Google Play Store
iOS 12.1 or higher
ATTENTION:
With the key out of the
ignition, disconnect the negative battery
terminal before installing this product. Ensure
that all installation connections, especially the
air bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
REV. 2/7/23 INSTAXDSPX-A2B3

Publicidad

loading

Resumen de contenidos para Axxess AXDSPX-A2B3

  • Página 1 • Zip ties Apple App Store • LD-DSP-A2B-4 • AXBK-1 Google Play Store iOS 12.1 or higher • AXDSPX-A2B3 interface harness • A2B-EXT (male connectors: 12-pin, 16-pin) INTERFACE FEATURES • Designed for Revel A2B amplifiers • Independent equalization on each of the 10 outputs • A2B data interface w/AXDSP-X (digital signal processor) built-in •...
  • Página 2 Assignable outputs labeled AXBK-1 current of all amps exceed 1-amp. CH 7-10 to be used for optional amps. Factory Amp AXDSPX-A2B3 (must be removed) Interface Brown/Yellow - Subwoofer Right + Brown/Blue - Subwoofer Right - Green/White - Subwoofer Left +...
  • Página 3 7. Connect the amp turn-on wire from the AXDSPX-A2B3 harness. 8. Click the Identify button to confirm that the AXDSPX-A2B3 is connected properly. If so, a chime will be heard from the front left speaker or gauge cluster. Test all functions of the installation for proper operation.
  • Página 4 Contact our Tech Support line at: 386-257-1187 • If the Red light in the AXDSPX-A2B3 interface is blinking, it is not communicating with the vehicle. Remove the key from the Or via email at: ignition, unplug the connectors from the interface, then inspect all connections made. If everything is proper, connect the techsupport@metra-autosound.com...
  • Página 5 • Cinta • Arnés AXDSPX-A2B3 (conectores hembra: negro de 12 • Cortador de cables • Abrazaderas de plástico • Arnés de interfaz AXDSPX-A2B3 pins, gris de 20 pins) (conectores macho: 12 pins, 16 pins) • AXBK-1...
  • Página 6 1 ampere amplificadores opcionales. Conector USB del Interfaz Amplificador de Fábrica AXDSPX-A2B3 Café con amarillo: Subbafle derecho + Café con azul: Subbafle derecho - Verde con blanco: Subbafle izquierdo + Blanco con rojo: Subbable izquierdo -...
  • Página 7 Nota: Asegúrese de que el conector USB del amplificador de fábrica esté conectado al AXDSPX-A2B3. 3. Conecte los conectores de 12 pins y 16 pins del arnés AXDSPX-A2B3 a la interfaz AXDSPX- A2B3. 4. Descargue la aplicación AXDSP-XL desde Google Play Store o Apple App Store e instálela.
  • Página 8 Póngase en contacto con nuestra línea de soporte técnico en: • Si parpadea la luz roja en la interfaz AXDSPX-A2B3, eso quiere decir que no se está comunicando con el vehículo. Quite la 386-257-1187 llave de la marcha, desconecte los conectores de la interfaz y proceda a revisar todas las conexiones que se realizaron. Si O por correo electrónico a:...