Hcalory SKUJ08387 Manual Del Usuario página 7

Minimum wind speed setting → Press the up or down button to adjust the minimum wind speed setting
7.
8.
(1360PRM-2600PRM). It can be modified as needed. Press the set key to enter the next item.
Maximum wind speed setting → press the up or down button to adjust the maximum wind speed setting
9.
(3000PRM-5000PRM). It can be modified as required. Press the set key to enter the next item.
Temperature control mode setting → press up to set automatic temperature control mode → press
10.
down to set manual temperature control mode. It can be modified as needed.
Modify password management → press the key to adjust the value, press the up key to confirm to enter
the next digit, and modify the following values in turn
Note: After the parameter setting is completed, you must press the setting key to confirm and exit
before saving the parameter setting. If you exit the parameter setting automatically, the data will not be
saved. Please carefully check each newly entered password and save it so that you can enter to
change the parameters next time. (No special requirements are not recommended to modify by
yourself)
6.7 Remote Control Operation Instructions(NO.7)
Overall display:
:Off button;
【 】 【 】: Gear/temperature/item adjustment button;
M: Mode switch/setting key
screen display area
Operating mode
①In manual mode, the setting gear can be adjusted within the range of 1~10;
②In automatic mode, the setting temperature can be adjusted within the range of 8~36℃, and the gear
of the control switch changes with the temperature in the cab. When the temperature rises or falls, the
control switch will automatically adjust the running gear.
Quickly reach the set temperature, allowing the heater to operate more intelligently and economically.
③ When a fault occurs during operation, the fault code will be flashed on the display window of the
control switch to facilitate more accurate and intuitive finding of the fault.
- English 010 -
Instructions:
】to turn on when the machine is off; press 【
On/Off: Press【
machine is on;
Mode switching: press 【M】 in constant temperature mode to switch to gear mode, and press 【M】
in gear mode to switch to constant temperature mode;
】running gear/temperature +1, the maximum is 10 gears/36℃, press【
Gear adjustment: press【
】running gear/temperature-1, the minimum is 1 gear/8℃;
Time setting: In the power-on state, the screen displays the current time, long press the [M] key for 3s
to enter the time setting:
Item 1: Set the current time, press【M】key to set, press【
Item 2: Set the automatic start time, the setting method is the same as above;
Item 3: It is the running time after automatic startup, the setting method is the same as above, and the
switching unit is 0.5 hours;
Item 4: It is the ON/OFF setting for the auto-start function. After the auto-start function is turned on, the
alarm clock icon on the screen is always on.
Engineering mode: Press 【 】 【
press 【 】 item +1, press 【 】 item -1, the display area displays data items in engineering
mode;
001: Heater motherboard version number; 002: Fault code; 003: Shell temperature; 004: Power supply
voltage;
005: Heater running gear; 006: Cab temperature; 007: Altitude;
Remote control matching: In the power-on state, press and hold 【
'rte', then press any button on the remote control, the matching is successful, and it will automatically
return to the running interface after success;
Language switching: Press and hold【M】 【
and switch circularly according to the sequence of 'English', 'German', 'Russian' and 'Voice off';
Oil pumping mode: Press and hold the 【
starts a 300s countdown, starts pumping oil, and automatically exits when the countdown ends, and
cannot be manually exited except when the machine is turned off;
Fault display: When the heater fails, the fault code will flash in the display area, and the fault type is
shown in the table below;
- English 011 -
】to turn off when the
】 【 】to switch;
】 simultaneously for 3s to enter the engineering mode,
】 for 3s, the screen displays
】for 3s at the same time in the power-on state to switch,
】key for 7s in the shutdown state, the display area