Teuco T01M Instrucciones De Montaje página 29

FITTING THE ROOF
-
11
Fit the roof to the columns of the hydroshower, inserting the
A
wires (art. T01M and HT1M only) and the hose through the
holes as indicated.
-
11
Fit the bracket to the column with the taps and secure the roof
B
with screws and washers.
-
11
Screw the showerhead onto the arm fitted previously.
C
-
11
Slip the screw clip over the hose (5), fit the hose to the union
D
and tighten the clip.
ART. T02M - HT2M ONLY
FITTING THE COLUMN SIDE TRIM
12
- Fix the trim to the wall bracket with the screws as indicated.
ART. T01M - HT1M ONLY
FIXING THE BACKLIT PANEL
12
- Seat the neon tube in the angle moulding fixed to the wall
A
previously.
12
- Secure the neon tube to the moulding, undoing and then
B
retightening the screw.
12
- Secure the other neon tube to the seat column with the screws.
C
12
- Plug the connectors onto the neon tubes.
D
-
12
Locate the backlit panel against the springs of the seat column.
E
12
- Secure the panel to the angle moulding with screws and
F
washers.
12
- Clip the vertical trim onto the moulding.
G
12
- Position the top trim on the backlit panel, making certain it is the
H
right way round, secure with the screw and apply silicone
sealant at the point indicated.
FITTING THE TOP TRACK AND ADJUSTING THE SLIDING
DOOR
13
- Clip the backstop to the door.
A
13
- Preassemble the sliding door and top track.
B
13
- Clamp the track and door to prevent movement, by securing the
C
tube with the screw as indicated.
13
- Proceed to fit the sliding door:
D
first, to the bottom track, removing the tube by pulling on the
sticker (see drawing - steps 1 and 2);
then under the roof, clipping the opposite end of the top track
onto the angle moulding (step 3).
13
- Keep the door open!
E
Secure the top track to the angle moulding with the screws.
13
- Secure the top track to the roof with the bearing hanger and the
F
screws.
FITTING THE DOOR
14
- Fit the clip-on seal to the column side trim, making certain it is
A
the right way round.
14
- Fit the door seal in the position indicated.
B
Fit the door and the side trim with the screws.
14
- Align the door by means of the screws indicated in the drawing.
C
ADJUSTING THE SLIDING DOOR
15 /
- If the height of the door needs adjusting, remove the safety
A B
caps and work the bolts up or down as necessary.
FITTING THE FRONT COVER TRIM
16
- Position the front cover trim over the taps column between the
bathtub rim and the roof, and fix with the screws and washers.
FITTING THE ROOF COVER TRIM
17
- Position the top cover trim on the roof and secure with the
screws removed previously.
FITTING THE BATHTUB PANELS
-
18
Refit the panels removed previously, in the sequence indicated: 1, 2:
- offer the panel to the bathtub
- press the top edge of the panel inwards so that it locates between
the springs and the rim of the tub.
Raise the panels using the wedge (A) provided.
- Secure the panels with the screws and collars (B).
- Snap the concealers (C) onto the collars.
FITTING THE WALL TRIMS
-
19
The trims kit supplied is suitable for all versions; use only the pieces
needed.
L1 + L6 = 1560 Cut in two pieces, each to length as indicated
L2 + L5 = 1560 Cut in two pieces, each to length as indicated
L3 =1560 - Grey trim to be cut to size = 1485
L4 =1560 - Grey trim to be cut to size = 1485
Apply silicone sealant to the faces in contact with the wall and with the
hydroshower.
Fit the trims with the relative angles and terminals, being certain to
ensure faultless contact with the hydroshower and with the wall.
Apply adhesive tape to hold the trims correctly in place; wait at least 4
hours, then remove the tape and clean off excess sealant.
29 29