Smeg SE232TD1 Instrucciones Para La Instalación página 16

Flash Cooking
(Automatic cook start)
This function facilitates cooking as
you do not need to be present while it
is being done. The touch control pre-
programmes the chosen hot plate at
the maximum power and subsequently
lowers it to the desired power level
(which you have selected) after an
approximate amount of time (see
table 1).
Table 1
Automatic Cook Start
Selected
Function
power
0
1 60
2 180
3 288
4 390
5 510
6 150
7 210
8 270
9
SWITCHING THE AUTOMATIC
COOK START FUNCTION ON
1 The hot plate must be selected.
2 Select power 9 and then press
power touch key (5).After using
the touch key you must lower the
continuous cooking power to the
desired level, (for example 6). When
the automatic cook function starts
"A" indication flashes with desired
power level on the display.
SWITCHING THE AUTOMATIC
COOK START FUNCTION OFF
After at least 10 seconds have elapsed
since the beginning of the automatic
cook start function:
1 The hot plate must be selected.
2 Press touch key
indicator reaches level 9 and the
automatic cook start function will be
deactivated.
Timer Function
This function makes it easier to cook,
as you do not need to be present
throughout the process: the timed hot
plate(s) will switch off automatically
after the set time has lapsed. There is a
separate timer for each hot plate, which
allows all of the hot plates to be timed
simultaneously.
With these models you can use the
clock as a timer for the hotplates for
times ranging from 1 to 99 minutes. All
the cooking areas can be programmed
individually and in a simultaneous
manner.
0
TIMING ONE HOTPLATE
1 The cooking zone to be timed must
be selected.
2 Select a power level for the hotplate
from 1 to 9 using the touch keys
or (5/4).
3 Press clock touch key
Timer indicator (11) will display 00.
-
Depending on the model, the timed
cooking surface indicator (12) will
flash.
On the power indicator (3),
during the time set.
4 Immediately afterwards, enter a
cooking time between 1 and 99
minutes, by using the touch keys or
(5/4).
When the power indicator (3) stops
flashing, it will start to count down the
time automatically. The respective
timed hotplate disolay (11) will continue
flashing.
Or, when the countdown starts, the
relevant power level and
alternately on the power indicator (3)
of the relevant heater area.
When the clock reaches 01, it will
switch from counting down minutes
to seconds.
(5) till the
Once the selected cooking time has
elapsed, the heating zone being timed
is turned off and the clock emits a series
of beeps for several seconds. The
timer indicator will display a flashing
00 beside the hotplate that has been
disconnected.
If you wish to time another hotplate at
the same time, repeat steps 3 and 4.
If the heating zone turned off is hot, its
indicator displays an H or otherwise an
0. To turn off the audible signal touch
any sensor.
CHANGING THE PROGRAMMED
TIME
To change the progrmmed time, you
must press the touch key of the timed
hotplate (2) to select it and then the
clock
read and
change the time.
DISCONNECTION OF THE TIMER
If you want to stop the timer before the
programmed time is up
1 First select the hotplate and then
press clock touch key
(10).
2 Use the touch key
the time to 00. The clock is cancelled.
Alternative method :
After zone selection if timer touch key
is pressed for two seconds, the related
will flash
timer will be cancelled.
Safety switch off function
If due to an error one or several hot
plates do not switch off, the appliance
will be automatically disconnected after
a set amount of time (see table 2).
Table 2
Selected
power
level
will flash
1
2
3
4
5
6
7
8
9
EN
(10). You may then
(10).
(4) to recude
MAXIMUM OPERATION
TIME
(in hours)
10
5
5
4
3
2
2
2
1
15