Intex PureSpa SSP-H-20-1C Manual Del Propietário página 19

Spa Tub Drainage
Turn off the spa control unit.
1.
Connect the drain valve adaptor to a garden hose and point the other end
2.
of the garden hose to a suitable draining area (see drawing 14).
Remove the drain valve cap from outside of the spa tub and attach the
3.
drain valve adaptor to the drain valve (see drawing 14).
From inside of the spa tub, open the drain valve cap, water will start
4.
fl owing out from the garden hose.
When the water stops draining, disconnect the spa control unit from
5.
the spa tub wall. Lift the spa tub wall from the side opposite the drain,
leading any remaining water to the drain and emptying the spa completely
(see drawing 15).
Attached the infl ation hose (7) to the air blower infl ation outlet on the
6.
control unit.
Turn on the spa and press the
7.
inlet/outlets on the spa tub and spa control unit to dry out any water in the
piping system (see drawings 16 & 17).
Use a clean towel to wipe up any remaining water and moisture on the
8.
spa tub and spa control unit.
Ensure the spa tub and spa control unit are thoroughly dried.
9.
NOTE: The enclosed plugs (15) can be used to cover the water inlet and
outlet connectors from the inside of the spa tub to prevent water from
fl owing out.
Spa Tub Cleaning
If dirt is visible in the water or water becomes cloudy and proper water
chemistry does not clear it up, change the water and clean the spa tub.
See "Spa Tub Drainage" section on how to drain the spa.
While empty, remove the cartridge housing from inside of the spa tub wall,
clean and/or replace the fi lter cartridge. Use a sponge and mild soap solution
to wipe away any soil or stains on the inside of the spa wall. Rinse thoroughly
before refi lling with clean water.
IMPORTANT: Do not use steel wool, hard brushes or abrasive cleaners.
Spa Tub Air Valve Fastening
Check the spa tub air valve for leakage and tightness before use. If air is leaking
from the air valve, use the provided wrench (22) to tighten the air valve as follow:
Make sure the spa tub is defl ated, open the air valve cap and insert the
1.
wrench (22) into the air valve body (see drawing 18).
With one hand, hold the backside of the air valve base from the inside of
2.
the spa tub wall and turn the wrench (22) clockwise.
IMPORTANT: Never adjust the air valve base when the spa is in use or
fi lled with water. Only use the air valve wrench if the air valve is loose or
there is leakage around air valve base. Do not over tighten the air valve: over tightening can damage the
valve. Just ensure the air valve is snug and not leaking.
Spa Cover
The attachment buckles of the cover are locking buckles. Two keys are provided in the plastic bag with the
manual and other accessories. Each buckle is marked with "locked" and "unlocked" symbols for easy operation:
put the key into the slot on the buckle and turn it to the appropriate position to lock or unlock the buckle
respectively.
To assure safety from unauthorized access, always put the cover on when spa is not in use and lock all buckles.
Always keep the keys out of reach of children. In case you misplace the keys, you can use any similar size fl at
screwdriver to lock or unlock the buckles.
Inspect the spa cover regularly for leaks, premature wear and tear, damage, or signs of deterioration. Never use
a worn or damaged cover: it will not provide the level of protection required to prevent unsupervised access to the
spa by a child.
S AVE THESE INSTRUCTIONS
(295IO) SPA ENGLISH 7.5" X 10.3" PANTONE 295U 08/20/2016
MAINTENANCE
button, aim the infl ation hose at the
295
English
A
14
11
1
2
3
15
16
7
17
7
18
22
Page 18