Publicidad
Idiomas disponibles
Idiomas disponibles
EN
ORIGINAL INSTRUCTIONS
SPECIFIED CONDITIONS OF USE
The rotary hammer can be used for hammer drilling, chiselling in
stone and concrete, and drilling in wood, metal, and plastic.
Do not use the product for any other purpose.
WARNING! Read all safety warnings, instructions,
Failure to follow all instructions listed below may result in electric
HAMMER SAFETY WARNINGS
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Exposure to noise can cause hearing loss.
high output torque and without properly bracing the tool during
Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
SAFETY INSTRUCTIONS WHEN USING LONG DRILL BITS
WITH ROTARY HAMMERS
At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting the workpiece, resulting
Bits can bend, causing breakage or loss of
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use the dust collection device or connect a dust extraction vacuum
when operating the product.
Clamp the workpiece with a clamping device. Unclamped
immediately if it stalls.
Do not switch on the product again after it has stalled. Switching it
on again can cause a kickback with high reaction force. Determine
why the product has stalled and rectify it, paying heed to the safety
instructions.
The dust produced when using the product may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Remove the battery pack before starting any work on the product.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING!
product damage due to a short circuit, never immerse your tool,
chemicals, and bleach or bleach containing products, etc., can
cause a short circuit.
Do not dispose of used battery packs in the household refuse or
protect our environment.
Battery packs that have not been used for some time should be
recharged before use.
For an optimum lifetime, the battery packs have to be fully charged
after use.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C and
away from moisture.
Loss of control
This tool produces a
• Store the battery packs in a 30% - 50% charged condition.
• Every six months of storage, charge the pack as normal.
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
If the product does not start up again, the battery pack may have
discharged completely. Recharge the battery pack.
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national, and international provisions and regulations.
• Batteries can be transported by road without further requirement.
• Commercial transport of lithium-ion batteries by third parties is
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that the battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that the battery pack is secured against movement within
the packaging.
• Do not transport batteries that are cracked or leaking.
• Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 2.
1. Direction of rotation selector
2. Rafter hook
3. Anti-vibration system
4. Depth guide rod
5. SDS chuck
6. Drill bit
7. Mode selector
8. Variable speed switch trigger
9. Auxiliary handle, insulated gripping surface
10. LED light
11. Handle, insulated gripping surface
12. Battery pack
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics
are susceptible to various types of commercial solvents and may
be damaged by their use. Use clean cloths to remove dirt, carbon
dust, etc.
Use only AEG accessories and spare parts. Should components
that have not been described need to be replaced, contact one
addresses).
If needed, an exploded view of the product can be ordered. State
the product type and the serial number printed on the label,
and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364
Winnenden, Germany.
SYMBOLS
Read the instructions carefully before starting the
product.
CAUTION! WARNING! DANGER!
Anti-vibration system
EN
DE
FR
IT
ES
PT
NL
DA
NO
SV
FI
EL
TR
CS
SK
PL
HU
SL
HR
LV
LT
ET
RU
BG
RO
MK
UK
AR
11
Publicidad
