Ilustrated Description - stayer PR10EK Manual De Instrucciones

WARNING: Never tighten the fasting nut of the
claw without a milling cutter being housed therein.
Otherwise, the claw may become deteriorated.
EXTRACTING THE CUTTERS (PR12E)
Take into account the instructions for "installing the
cutters".
Loosen nut "Q" counterclockwise using wrench "V". With
nut "V" loosened, withdraw the milling cutter. If the milling
cutter does not drop out by its own weight, smoothly knock
on the nut to release the milling cutter. Always clean the
claw, the thread of the axle and thread of the axle of the
nut.
----------------------------------------------------------------------------
PARALLEL GUIDE (fig.3-4)
Position the parallel guide "A" and its guide rods.
The parallel guide is to be secured to the rods by the two
locking nuts "R".
ROUTER BASE OF THE MACHINE
Router base "O" is connected to the cutter and allows the
machine to follow a special cutting profile.
All the cutters must be fitted in the guiding platform slot,
whose diameter limits that of the cutter to use.
When using the cutter on delicate surfaces
as decorations or finishes, remind covering
the decorative surfaces or those of the cutter
base well with adhesive tape or another
protection means.
STRAIGHT GUIDE - PR12E (Fig. 18)
1. Straight guide.
2. Precision adjustment screw.
3 and 4. Guide fastening wing nut.
5. Guide carrier.
The straight guide is useful for making straight cuts when
making bevels or grooves (PR10E-PR12E).
Place the guide for straight cuts onto the guide fastener
with the fastening screw (3). Insert the fastener of the
guide into the openings of the base of the tool and tighten
the fastening wing nut (4). To adjust the distance between
the milling cutter and the guide for straight cuts, loosen
fastening screw (3) and rotate the precision adjustment
screw (1.5 mm or 1/16'' per each turn). At the desired
distance, tighten fastening screw (3) to fasten the guide
for straight cuts in its place (PR12E).
By using the convenient holes of the guide to screw
extra wooden pieces, one may make a straight guide
that is wider, of desired dimensions (PR10E-PR12E).
(Figs. 19-20).
1. Straight guide.
2. More than 15 mm (5/8'').
3. Wood.
When using a milling cutter having a large diameter, place
wooden pieces having a thickness of more than 15 mm
on the straight guide, to avoid the milling cutter striking
the straight guide.
ENGLISH
17
When cutting, move the tool with the straight guide at level
with the side of the work piece.
If the distance between the side of the work piece and the
cutting position is too wide for the guide for straight cuts,
or if the side of the work piece is not straight, the guide
for straight cuts may not be used. In this case, fasten the
straight board to the work piece with the clamp, and use it
as a guide against the base of the router. Feed the tool in
direction of the arrow.
CUT-OUT GUIDE - PR12E (figs. 22 and 23)
1. Straight guide.
2. Adjustment screw.
3. Fastening wing nut.
4. Fastening wing nut.
5. Guide carrier.
6. Upper fastening screw.
With the cut-out guide it is easy to male cut-outs, curved
cuts in sheets for furniture and other cuts of similar kinds.
The guide roller follows the curves and guarantees a fine
cut. (PR12E).
Place the cut-out guide on the guide fastener with the
fastening screw (3). Insert the guide fastener into the
openings of the base of the tool and tighten the fastening
screw (6). To adjust the distance between the drill bit and
the cut-out guide, loosen fastening screw (3) and rotate
the precision adjustment screw (1.5 mm or 1/16'' per
each turn). When adjusting the guide roller upwards or
downwards, loosen fastening screw (4) (PR12E).
After adjusting, tighten the fastening screws firmly (PR12E).
7. Tip.
8. Guide roller.
9. Work piece.
When cutting, move the tool moving the guide roller along
the side of the work piece (PR12E) (Fig. 24).

3.3 Ilustrated description

A. Parallel guide set.
B. Variable speed adjustment.
C. Locking guide.
D. Adjustment of head's upper position.
E. Brush cover (PR12E).
F. Guide roller.
G. Depth scale
H. Depth stop.
I. Depth stopper turret.
J. Carbon brushes (PR12E).
K. Depth-scale locking knurled screw.
L. Depth-scale adjustment knob.
M. Safety switch control element.
N. Immersion block lever.
O. Inner guide.
P. Useful for cutting holes.
Q. Flat wrench.
R. Locking control of the parallel guide.
S. Machine base.
T. Locking button.
U. Locker inner guide "O" (PR12E).
V. Clamp nut.
17