Repair Service; Technical Data; Disposal And Recycling - stayer PR10EK Manual De Instrucciones

TEMPLATE SIZE
The size of the template will be determined by the size of
the cutter to be used. Take into account the indications in
figures 14-15 when calculating the overlap distances.
CUTTING DIRECTION
To avoid vibrations in the cutter and to obtain a better
result, cuts must be made counterclockwise at the time of
outer cuts and clockwise at the time of inner cuts (fig. 16).
5. Maintenance and service instructions
1. Always disconnect the tool before carrying out any
inspection or cleaning. Never use water or other liquids
to clean the tool. Clean the tool with a cloth or brush.
2. Replace used, worn-out cutters.
3. The tool's cooling vents must be cleaned from time to
time to avoid excessive heating-up of the motor.
4. Always check that the components of the tool are
mounted solidly.
5. The casing must always be without any indication of
cracks or any other damages.
6. Always check that the cable is in a perfect condition.

5.1 Repair service

The technical service will advise you regarding your
inquiries on repairing and servicing your product as well
as on spare parts.
Our team of technical advisors will be pleased to guide
you in respect of acquiring, applying and adjusting the
products and accessories.
Stayer Ibérica S.A.
Área Empresarial de Andalucía - Sector 1
Calle Sierra de Cazorla nº7
CP: 28320 Pinto (Madrid) Spain.

5.2 Disposal and recycling

The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
OnlyforEC countries:
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/
EC for Waste Electrical and Electronic
Equipment and its implementation into national
right,power tools that are no longer usable
must be collected separately and disposed of
in an environmentally correct manner.
Subject to change wlthout notlce.
5.3 Warranty
Warranty card
lncluded in the documentation that accompanies this
equipment, you should find the warranty card. You should
fill out the card completely and retum to vendar with a copy
of purchasing receipt or invoice and you should receive a
receipt.
ENGLISH
19
Note: lf you cannot find the warranty card within
the documentation,youmust ask for it through your
supplier.
The warranty is limited only to manufacturing defects and
expire if pieces have been removed or manipulated or
repaired otherthan themanufacturer.
6. Regulations

6.1 Technical Data

= Power
= Load speed
= Cutting depth
= Clamp size
= Weight
The values givenarevalid for nominalvoltages [U]230/240
V-50/60 Hz - 110/120 V - 60Hz. For lower voltage and
models for specific countries, these values can vary.
NoiseNibration lnformation
Noise determined according to EN 60745 (Plywood).
The typical sound pressure level of appliance determined
with a filter A product are: Sound pressure level 89 dB(A);
sound power level 100 dB(A). Tolerance K=3 dB.
Use protection!
Total vibration values (vector sum of three directions)
determined according to EN 60745: Sanding drywal
a=5,5 m/s , K= 2,5 m/s
2
The vibration emission level given in this information sheet
has been measured in accordance with a standardised
test given in EN 60745 and may be used to compare
one tool with another. lt may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications,with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure leveloverthe
totalworking period.
An estimation of the levelof exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job.
19
.
2