Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
8) SWR ADJUSTMENT
This function allows to adjust the SWR (Standing Wave Ratio) by beep tones.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use the UP/DN buttons (18) on the micro-
phone to
select
the SWR function.
2.
Press the rotary PUSH knob (6). The radio automatically goes to
without pressing PTT switch (17) . The SWR measurement starts. Measurement
time is 5 minutes maximum. The remaining time is displayed.
3.
Adjust your antenna.
4.
The beep tone* is continuous when SWR value is equal to1. 0 . The space
between two beeps became longer when SWR value moves away from1. 0 .
Volume of the beep tone is adjustable with VOLUME knob (1).
Display shows the SWR value. For example 2. 5 .
6.
Press PTT switch (17) to
exit
MENU mode.
*Please check that the beep volume is set to a comfortable listening level.
See § HOW TO ADJUST SWR page 33.
9) MIC TYPE
The PRESIDENT WALKER II can be used with an electret microphone as well
as with the dynamic one, 6-pin PRESIDENT (see the cabling diagram page
60). Turning on the unit, the type of the microphone is briefly displayed.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the MIC TP function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the type on the microphone EL (electret) or DY (dynamic).
4.
New press PUSH knob (6) to validate. The parameter stops blinking. a) Go to
point 1 to
adjust
another function or b) Press the PTT switch (17) to
and
exit
MENU.
disappears.
5.
exits
If no key is pressed, the unit
the display.
Default type of microphone is EL (electret).
10) PA SETTING
This function allows to
select
the operating mode of Public Address.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the PA SET function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the operating mode of the PA : I n, OF or PA or.
enter
MENU.
is displayed.
TX
disappears in the display.
enter
MENU.
is displayed.
The current parameter blinks on LCD.
MENU after 10 seconds,
disappears in
enter
MENU.
is displayed.
The current value blinks on LCD.
4.
New press PUSH knob (6) to validate. The parameter stops blinking. a) Go to
point 1 to
adjust
another function or b) Press the PTT switch (17) to
exit
MENU.
and
5.
If no key is pressed, the unit
the display.
modulation of the microphone
I n: the
mode
connected to jack PA.SP. (D). The
internal loudspeaker [or external optional loudspeaker connected to jack
EXT.SP (C)]."PA" flashes alternately with the modulation mode used (AM,
FM or FM UK).
OF: The reception is no more functional. Only the
phone
is transmitted to the Public Address loudspeaker connected to jack
PA.SP. (D). PA and
PA: the
modulation of the microphone
ted to the Public Address loudspeaker connected to jack PA.SP. (D). "PA"
flashes alternately with the modulation mode used (AM, FM or FM UK).
The MIC GAIN knob (4) to
Default PA setting is: I n.
See § PA (Public Address) page 36.
11) RESET
Restores all factory settings.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the RESET function.
2.
Press PUSH knob (6) to
3.
New press PUSH knob (6) to reset. The unit
4.
If no key is pressed, the unit
validate
press on PUSH knob(6) key.
E) FUNCTIONS WITH PTT SWITCH
2 additional functions are available. TALKBACK and TALKBACK LEVEL.
1) TALKBACK
This function allows you to
or external speaker connected to the EXT jack. MS. (C).
Press and hold the PTT switch (17) and then press the F key (9) to
deactivate
the TALKBACK function. When the function is activated, "TALK-
BACK" is displayed.
39
disappears.
exits
MENU after 10 seconds,
is transmitted to external loudspeaker
received signal
modulation of the micro-
PA
volume level are displayed.
and the
received signal
adjust
the audio level of the mode PA.
enter
MENU.
validate.
AL blinks on LCD.
exits
MENU.
exits
MENU after 10 seconds or by a new long
hear
your own modulation in the optional internal
validate
disappears in
is transmitted to the
are transmit-
is displayed.
disappears.
activate
/
Publicidad
Tabla de contenido
