Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
A) DC-POWER TERMINAL (13,2 V)
B) ANTENNA CONNECTOR (SO-239)
C) JACK FOR EXTERNAL OPTIONAL SPEAKER (8 Ω, Ø 3.5 mm)
D) JACK FOR PA OPTIONAL SPEAKER (Public Address) (8 Ω,
Ø 3.5 mm)
E) JACK FOR OPTIONAL VOX MICROPHONE (8 Ω,Ø 2.5 mm)
C) FUNCTION TURNING ON THE UNIT
select
the FREQUENCY BAND turn off the unit. Press and hold the F key
To
(9) and then turn the unit on.
(Configuration: EU; PL; d; EC; U; In)
The frequency bands have to be chosen according to the country of use.
Don't use any other configuration. Some countries need a user's licence.
See table page 62.
1.
Turn on the power while pressing the F key (9). The letter corresponding to
the current configuration is blinking.
2.
In order to change the configuration, use the PUSH rotary knob (6) on the
unit or the UP/DN buttons (18) on the microphone.
3.
When the configuration is selected, press the F key (9) during 1 second. The
letter corresponding to the configuration is continuously displayed and a
confirmation beep sounds.
4.
At this point, confirm the selection by switching off the transceiver and then
switching it on again.
See the frequency bands table at pages 57 to 59 / configuration table
page 61.
D) MENU
The order of 11 functions is as described in this manual. However, the func-
tion displayed by entering the MENU will be the last function modified by
user.
The procedure is the same Whatever the function is:
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
select
to
the menu.
2.
Press PUSH knob (6) to
validate.
on the display.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
modify
the value of the parameter.
4.
New press PUSH knob (6) to
enter
MENU.
is displayed.
The parameter of the chosen function blinks
validate
the chosen value. The parameter
stops blinking and if the function has more than one parameter, the next
parameter blinks.
5.
If no key is pressed, the unit exits MENU after 10 seconds.
the display.
Note: UP/DN buttons (18) on the microphone have the same effect as the
rotation of the rotary PUSH knob (6). PTT switch (17)
and
exists
MENU.
disappears.
1) COLOR
This function allows to
choose
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the COLOR function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (11) on the microphone
to
select
the color. 7 available colors over and over :
4.
New press PUSH knob (6) to
blinking. a) Go to point 1 to
(17) to
validate
and
exit
MENU.
5.
If no key is pressed, the unit
the display.
Default COLOR is
(red).
2) KEY BEEP
When the function is activated, a beep
changing the channel etc. "BP" appears on the display when the function
is active.
Press PUSH knob (6) for 3 seconds to
1.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
select
the KEyBEEP function.
2.
Press PUSH knob (6) to
validate.
3.
Turn the rotary PUSH knob (6) or use UP/DN buttons (18) on the microphone
to
activate
On /
deactivate
4.
New press PUSH knob (6) to validate. The parameter stops blinking. a) Go to
point 1 to
adjust
another function or b) Press the PTT switch (17) to
and
exit
MENU.
disappears.
5.
If no key is pressed, the unit
the display.
Default KEY BEEP is On.
37
disappears from
validates
the last setting
the backlight color of the LCD.
enter
MENU.
is displayed.
The current COLOR blinks on LCD.
validate
the chosen color. The parameter stops
adjust
another function or b) Press the PTT switch
disappears in the display.
exits
MENU after 10 seconds,
sounds
when a key is pressed, by
enter
MENU.
is displayed.
The current status blinks on LCD.
Of the function.
exits
MENU after 10 seconds,
disappears in
validate
disappears in
Publicidad
Tabla de contenido
