Normatec 3 Instrucciones De Uso página 7

ADJUST THE PRESSURE LEVEL
Adjust the pressure level of the session by pressing the pressure level adjustment button on
the left of the level indicators. Pressure level 1 is the gentlest setting. The massage becomes
more intense as the pressure level is increased. Level can be adjusted while the session is
running. When level is adjusted during a session, the system will pause. Once you have finished
adjusting your level, press the Start/Stop button to resume treatment at the new pressure.
USE ZONEBOOST™
During your session, you can increase the intensity of a single zone with the ZoneBoost feature.
ZoneBoost is designed to be used when you want extra attention in a specific area. ZoneBoost
will add an extra 60 seconds of massage time, as well as 10 mmHg increased pressure, in the
selected zone. ZoneBoost can be enabled before or during a session. Only one zone can be
boosted at a time. To boost a zone press the ZoneBoost button until the LED indicator above
the zone you want to boost is lit up. To disable ZoneBoost press the ZoneBoost button until no
zone LED indicators are lit up.
The zones on the attachment are numbered in ascending order from distal zone to
proximal zone. So if you are using the leg attachments, Zone 1 would be your foot/ankle, Zone 2
would be your calf, Zone 3 your knee, Zone 4 lower quad and Zone 5 upper quad.
ADJUST THE SESSION TIME
Adjust the session time by pressing the time adjustment button on the left of the display
screen. The session time can be set to 15, 30, 45 and 60 minutes. Time can be adjusted while
the session is running. Tap the time adjustment buttons to cycle through the session time
options to add or subtract time from the session.
START THE SESSION
To start the session, tap the Start/Stop button.
PATENTED NORMATEC PULSE MASSAGE PATTERN
Before the patented Normatec Pulse massage pattern begins, you will experience a pre-inflate
cycle, during which the connected attachments are calibrated to your exact body shape.
Once the pre-inflate cycle is complete, the patented Normatec Pulse massage pattern will
begin by compressing your feet, hands, or upper quad (depending on which attachment you
are using). Similar to the kneading and stroking performed during a massage, each zone of
the attachments will first compress in a pulsing manner and then release as the compression
pattern works its way up your limb. When the top zone completes its massage, there will be a
brief rest period and then the cycle will begin again. This will repeat until the session time runs
out. When the session is resumed after a pause, the system will perform a pre-inflate cycle
before continuing.
STOP OR PAUSE THE SESSION
To stop the session at any time, tap the Start/Stop button. This will pause the session. To restart
your paused session, tap the Start/Stop button again. If you are done using the system, remove
the attachments from the hose, remove the attachments from your limbs, turn off the control
unit by pressing the power button, and disconnect the hose from the control unit.
To disconnect connectors from the junction box or the control unit, push the button on the
top of each connector while pulling away.
FINISH THE SESSION
The session will continue massaging until time runs out and the display reads Finishing Cycle.
The system will continue until the current cycle is finished. When the session is completed,
remove the attachments from the hose, remove the attachments from your limbs, turn off the
control unit by pressing the power button, and disconnect the hose from the control unit.
To disconnect connectors from the junction box or the control unit, push the button on the
top of each connector while pulling away.
TURN OFF THE CONTROL UNIT
To turn off the system, press the power button and confirm that the LED indicators and display
are off.
CONNECTING TO THE HYPERICE APP
To connect your system to the Hyperice App via Bluetooth
on, Bluetooth ® is turned on in your phone, and your control unit is within close proximity. Select
a routine within the Hyperice App and if prompted tap "Scan for Devices." Select your system
when it pops up on the screen. HyperSmart™ will automatically start your session, and adjust
pressure along the way.
CLEANING THE SYSTEM
To clean the control unit:
• Wipe down the system with a damp, clean cloth.
• Dry thoroughly with a clean cloth.
make sure the control unit is turned
®