Publicidad
Idiomas disponibles
Idiomas disponibles
GENERAL SAFETY RULES FOR WOODWORKING MACHINERY
15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools
sharp and clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
16. DISCONNECT TOOLS before servicing and when
changing accessories such as blades, bits, cutters.
17. USE RECOMMENDED ACCESSORIES. Consult the
owner's manual for recommended accessories. The use
of improper accessories may cause hazards.
18. AVOID ACCIDENTAL STARTING. Make sure switch is
in "OFF" position before plugging in cord.
19. NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is accidentally
contacted.
ADDITIONAL SAFETY RULES FOR TABLE SAWS
1. ALWAYS use saw-blade guard and spreader for every
operation for which it can be used, including all through
sawing. Thru-sawing operations those when the blade
cuts completely through the work piece as in ripping
or cross cutting.
2. ALWAYS hold the work firmly against the miter gage
or fence.
3. ALWAYS use a push stick for ripping narrow stock. Refer
to ripping applications in instruction manual where push
stick is covered in detail.
4. NEVER perform any operation "free-hand" which means
using your hands to support or guide the work piece.
Always use either the fence or the miter gage to position
and guide the work.
5. NEVER stand or have any part of your body in line with
the path of the saw blade.
6. NEVER reach in back of or over saw blade.
7. MOVE the rip fence out of the way when cross cutting.
8. WHEN cutting molding. NEVER run the stock between
the fence and the molding cutter head. Refer to molding
applications in instruction Manual for details.
9. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction or rotation of the blade or cutter
only.
ASSEMBLY INSTRUCTION
TOOLS PROVIDED FOR ASSEMBLY
1. Arbor-blade guard bracket wrench.
2. 12mm combination wrench.
3. Two Allen wrenches.
20. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly
and perform its intended function-check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting ,and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced.
21. DIRECTION OF FEED. Feed work into a blade or cutter
against the direction of rotation of the blade or cutter
only.
22. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Don't leave tool until it comes to a
complete stop.
23. NO DRUGS, ALCOHOL, MEDICATION. Do not operate
tool while under the influence of drugs, alcohol or
any medication.
10. NEVER use the fence as a cut-off gage when cross
cutting.
11. NEVER attempt to free a stalled saw blade without first
turning the saw OFF.
12. PROVIDE adequate support to the rear and sides
of the saw table for wide or long work pieces.
13. AVOID KICKBACKS (work thrown back toward you)
by keeping blade sharp. Keeping rip fence parallel to
the saw blade. Keeping splitter and ant kickback figures
and guard in place and operating, by not releasing work
before it is pushed all the way past the saw blade,
and by not ripping work that is twisted or does not have
a straight edge to guide along the fence.
14. AVOID awkward operations and hand positions where
a sudden slip could cause your hand to move into
the cutting tool.
15. NEVER use solvents to clean plastic parts. Solvents
could possibly dissolve or otherwise damage
the material. Only a soft damp cloth should be
used to clean plastic parts.
16. ALWAYS bolt the saw to the supporting surface or use a
sturdy outrigger support if a table extension more than
24 in long is attached to the saw.
ADDITIONAL TOOLS REQUIRED
1. Straightedge.
2. Large slot and large Phillips screwdrivers.
3. Socket Wrench (recommended) and Adjustable wrench.
2
Publicidad
