Publicidad
Idiomas disponibles
Idiomas disponibles
EN
1
DESCRIPTION
1.1
PURPOSE
The machine is used to illuminate the work area.
1.2
OVERVIEW
6
5
Auxiliary handle
1
Lens
2
Knob
3
2
GENERAL POWER TOOL
SAFETY WARNINGS
Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to
follow all instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-
operated (corded) power tool or BATTERY-operated
(cordless) power tool.
2.1
GENERAL POWER TOOL SAFETY
WARNINGS
•
Verify that the power tool is secure while transporting.
•
Store the power tool in a dry area that will prevent
unauthorized use or damage. Keep out of the reach of
children.
•
Keep handles dry, clean, and free of debris. Clean the
power tool after each use. Refer to the Maintenance
Section in this manual for more information.
•
Keep these instructions in a safe place for future
reference. Refer to them often and use them to instruct
other users. Anyone who uses this power tool must read
these instructions carefully.
•
Maintain the power tool with care. Follow the
instructions for lubricating and changing accessories.
1
4
Hook
4
Plug
5
ON/OFF switch
6
WARNING
English
2.2
ELECTRICAL SAFETY
•
To disconnect, turn all controls to the off ("O") position,
then remove plug from outlet.
•
Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
•
Unplug from outlet when not in use and before servicing
or cleaning.
•
Do not operate any product with a damaged (cord or)
plug, or after the product malfunctions or is dropped or
damaged in any manner. Return product to the nearest
authorized service facility for examination, repair, or
2
electrical or mechanical adjustment.
3
•
Don't Abuse Cord – Never carry product by cord or yank
it to disconnect from receptacle. Keep cord from heat, oil,
and sharp edges.
•
Disconnect the product from the power supply when not
in use, before servicing, when changing bulbs (lamp),
cleaning, and similar actions.
•
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw.
An undersized cord will cause a drop in line voltage,
resulting in overheating and loss of power. Use the chart
to determine the minimum wire size required in an
extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
•
Do not insert foreign objects into this product.
2.3
EXTENSION CORDS
•
Use only extension cords which have plugs and
receptacles which accept the product's plug. Replace
damaged extension cords.
•
When working outdoors with a product , use an extension
cord that is designed for outside use. This type of cord is
designated with "W-A" or "W" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
•
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized extension cord will cause a drop in line
voltage resulting in loss of power and overheating. The
table on the next page shows the correct size to use
depending on cord length and nameplate ampere rating. If
in doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
2.4
POWER TOOL USE AND CARE
•
If operating a product in a damp location is unavoidable,
then the product should only be connected to a circuit that
is protected by a ground-fault circuit-interrupter (GFCI).
Use of a GFCI reduces the risk of electric shock.
•
Store product indoors when not in use.
•
Keep out of reach of children.
•
Do not clean this product with a water spray or the like.
Follow manufacturers cleaning instructions.
4
Publicidad
