cecotec CONGA TRITON 5000 ULTRACLEAN & CAR Manual De Instrucciones página 26

ENGLISH
3. PRODUCT ASSEMBLY
Pressure washer function
Install the handle with the screw.
Fig. 2.
Slide the trigger gun hook into position.
Fig. 3.
Install the dust compartment into position.
Fig. 4.
Install the spray lance to the trigger gun. Fit the spray lance into the gun and rotate it until the
two parts are completely locked.
Fig. 5.
Connect the high-pressure hose to the trigger gun. Connect the silver end of the high-
pressure hose to the trigger gun and twist the nut as indicated to secure the connection.
Fig. 6.
Connect the high-pressure hose to the water outlet. Connect the other end of the high-
pressure hose to the water outlet on the washer and twist the black rotatable end-piece as
indicated to secure the connection.
Fig. 7.
Connect the garden hose to the water inlet. Connect the garden hose adapter (female
coupler) to the water inlet of the pressure washer, then thread your garden hose (male end)
into the garden hose adapter.
Fig. 8.
Turn the switch to the I position.
You may fill the soap tank with specific cleaning agent. Connect one end of the tube to the
soap tank and the other end to the inlet hole located on the bottom rear part of the housing
(remove previously the silicon cap).
Accessory for upholstery: Removes dust from sofas, couches, etc.
Accessory for corners: Specific for vacuuming corners, plinths, etc.
Drying accessory: Its shape allows blowing and drying liquids spilled on the floor.
360Brush: Special for tyre cleaning.
EasyClean bristles brush: For vehicle's body and headlights cleaning.
Vacuuming/blowing function
Insert the vacuuming tube into the vacuuming or blowing nozzle. Fig. 9
Connect the vacuuming tubes. Once they are attached, assemble them onto the vacuuming
hose.
Assemble the wet suction base or solids vacuuming base onto the end of the vacuuming
tubes.
50
CONGA TRITON 5000 ULTRACLEAN & CAR
Assemble accessory 22 onto the free nozzle.
Turn the switch to the II position.
Using the device
Bleed the device as follows prior to operation:
Turn on the appliance power switch.
Unlock the lever of the trigger gun.
Push the lever of the trigger gun, the device will switch on.
Let the device run (max. 2 minutes) until the water exits the trigger gun without bubbles.
Release the lever of the trigger gun.
Lock the lever of the trigger gun.
Note:
Dry running of more than 2 minutes leads to damage of the high-pressure pump. If the
appliance does not build up pressure within 2 minutes, switch the appliance off and check the
troubleshooting section.
Keep a distance of at least 30 cm when using the jet for cleaning painted surfaces to avoid
damage.
Place the device on a flat, stable surface. Operate the device in an upright position.
Fig. 10.
Make sure that the switch is set to the off position. Plug it into a power supply.
Fill the suction hose with water. Screw the suction hose into the water connection of the
appliance and insert it into the water source.
Open the water supply.
Hold the spray gun with both hands.
Direct the nozzle of the chosen accessory away from you towards the surface to be cleaned.
Unlock the trigger and press it until a constant amount of water flows through the nozzle, to
allow air trapped in the hose to escape.
Release the trigger.
Turn on the switch "PW(I)".
Fig. 11.
Hold the spray gun with both hands. Direct the water jet to the object to be cleaned and press
the trigger.
Release the lever of the trigger gun; the device will switch off again and stop the water jet.
High pressure remains in the system.
Warning: Beware of the kick-back when pressing the trigger.
ENGLISH
51
CONGA TRITON 5000 ULTRACLEAN & CAR