LUND 67710 Manual De Instrucciones página 8

PRODUCT CHARACTERISTICS
The portable blender is designed to prepare food. Thanks to its
built-in battery it is possible to prepare meals easily and quickly
by cutting and mixing food products, even in places where there
is no access to a power supply source. The product is intended for
domestic applications only, and not for any commercial use. The
correct, reliable, and safe operation of the appliance depends on
its proper use, therefore:
Read the entire manual before the fi rst use of the product and
keep it for future reference.
The supplier shall not be held liable for any damage resulting from
failure to observe the safety regulations and recommendations
specifi ed in this manual. Use of the product for purposes other than
those for which it was intended shall cause the loss of the user's
rights to the warranty and under statutory warranty.
EQUIPMENT
The product is delivered complete, but requires carrying out a
number of preliminary actions described in further sections of the
manual, before starting operation. The product is supplied with a
charging cord. Charger is not included.
SAFETY INSTRUCTIONS
Caution! Read all of the following instructions. Failure to do so may
result in electrocution, fi re, or personal injury.
FOLLOW THE INSTRUCTIONS BELOW
Do not use the product in an explosive environment containing
fl ammable liquids, gases or vapours.
Before starting the product, make sure that the product itself and
its accessories are not damaged. If any damage is discovered, it is
not allowed to start working with the product. Any damaged compo-
nents must be replaced at an authorised facility. It is not allowed to
repair the product on your own.
The product is intended for indoor use only. Do not expose the
product to any precipitation or moisture. If water and moisture enter
the product, the risk of an electric shock is signifi cantly increased.
Do not immerse the product in water or any other liquid.
The product can only be charged using the provided cord. Avoid
any contact between the cord and heat sources, oil, sharp edges or
moving parts. Damage to the charging cord increases the risk of an
electric shock. If the charging cord is damaged (e.g. it is cut or its
insulation is melted), immediately remove the plug from the socket
and return it to an authorised repair facility. Never use the prod-
uct if its charging cord is damaged. Repairing the charging cord
is forbidden. It must be replaced with a new one at an authorised
service centre.
Before installing, removing or adjusting the product accessories,
make sure that the appliance is not running and that its blades are
still. Exercise special care, when handling sharp parts of the prod-
uct. Do not touch blades in motion. The blades are very sharp and
there is a risk of injury, even if the blades are not moving. Special
care must be taken when handling any accessories equipped with
blades.
Make sure that the selected accessory has been installed correctly,
before starting the product.
Do not overload the product. The temperature of the housing must
not exceed 60 C. Overloading the product will accelerate its wear
O
and tear, lead to its damaging, and increase the risk of electro-
cution.
The product must be kept under supervision at all times during
operation.
The product may not be used for hard food processing, seeds,
bones, shells, ligneous parts of plants.
The product is not to be used by children. Keep the product and
8
O R I G I N A L
GB
its cord out of the reach of children. It is important to ensure that
children do not see the product as a toy.
Children should not be allowed to clean or maintain the product
without the supervision of an adult.
This product cannot be used by people with impaired physical and/
or mental abilities, or by people without experience in or under-
standing of the operation of the product, unless they are supervised
or instructed in the safe use of the product, so that they understand
the relevant operating risks.
PRODUCT OPERATION
Preparing for operation
Caution! The procedure described in this section must be carried
out when the appliance is unplugged from power supply. Make sure
that the blade of the product is still.
The product must be unpacked and all parts of the packaging com-
pletely removed. It is recommended to keep the packaging, as it
can be helpful for further transport and storage of the product.
Check the product for damage. If any damage is detected, do not
use the product until the damage has been repaired or the dam-
aged components replaced with new ones that are free of defects.
Clean the product according to the instructions specifi ed in the
"Product Maintenance" section.
Charge the appliance battery before fi rst use. To do this, connect
the charging cable plug to the charging socket (II). The plug is
equipped with a magnet which maintains the connection between
the plug terminals and the charging socket. Put the second plug in
the USB socket of the charger or other device which has a standard
USB socket with a current capacity of at least 1 A. During charging,
the red indicator light will come on and when charging is completed,
the white indicator light will come on. After charging, immediately
disconnect the cable from the USB socket and then from the ap-
pliance. Keeping the charged product connected to the charger for
too long may result in irreversible damage to the product.
It is not possible to use the appliance during charging. After charg-
ing, the product is ready for use.
Product operation
Solid foods intended for mixing should be cut beforehand into
approx. 1 cm pieces. Fill the product cup with food intended for
mixing. Do not overfi ll the cup. After mounting the cutting base and
inverting the cup, there should be a free space of at least approx. 1
cm between the bottom of the cup and unmixed food.
Mount the cutting base on the cup by screwing it in. Screw the
base in only with suffi cient force to ensure tightness. Use of ex-
cessive force can cause damage to the product. The appliance
will not operate if the base is insuffi ciently tightened or incorrectly
mounted base.
Turn the appliance so that the base is facing downwards, then hold-
ing the blender with both hands (III), start the blades by pressing
the power switch twice within a short interval of time.
Blades always operate at full speed. The appliance does not have
blade speed adjustment.
The appliance should not operate for more than 40 seconds. After
this time the blade rotation will be automatically interrupted. The
appliance can also be switched off at any time by pressing the
power switch.
After mixing, turn the blender so that the base is facing upwards,
wait a while for the base to leak and unscrew the base from the cup.
If the product does not start up when the power switch is pressed
twice and the red light illuminates three times, it means that the
battery is discharged. Charge the product before use.
If the blade stops during operation, e.g. when food is too hard to
mix, the appliance will automatically switch off and the white light
will fl ash. In this case, dismantle the lid, remove excessively hard
food and resume mixing.
A fully charged battery allows 10-15 operation cycles, 40 seconds
each. If hard food is mixed, the battery capacity may be lower. The
I N S T R U C T I O N S