Pump Oil Maintenance - Crafstman 500.752110 Instrucciones De Uso

8. Reinstall orifice a ndin-line filterintonozzle e xtension.
DO NOT overtighten orifice withallen wrench.
9. Reconnect nozzle e xtension tospray gun.
10.Make sure garden h ose is connected towater i nlet.
Check thathigh pressure hose isconnected tospray gun
and pump. Turn onwater.
11.Engage trigger l ock onspray g unand start e ngine
following i nstructions "How toStart Y our P ressure
Washer".
12.Test p ressure washer byoperating nozzle i nhigh and
lowpositions.
O-Ring Maintenance
Purchasean O-Ring Repair Kit at your local Searsor by calling
1-808-4-MY-HOME(469-4663) or online at www.sears.com.It
is not includedwith the pressurewasher.This kit includes
replacement o -rings, rubberwasher and water inlet filter. Referto
the instruction sheetprovidedin the kit to serviceyour unit's
o-rings.
WARHIHG
The high pressure stream of water that this
_ quipment produces can cut through skin and its
underlying tissues, leading to serious injury and
)ossible amputation.
* NEVER repairleakingconnections with sealant o f anykind.
Replace o-ringor seal.
Pump Oil Maintenance
DONOTattempt any oil maintenanceon this pump. This
model does not require any pump oil maintenance. The pump
is pre-lubricated and sealed from the factory, requiring no
additional lubrication for the life of the pump.
ENGINEMAINTENANCE
WARHJHG
_' Unintentional sparking can result in fire or
_¢ electric shock.
WHENADJUSTING ORMAKINGREPAIRS TO YOUR
PRESSURE WASHER
* Disconnect the spark plugwire from the sparkplugand place
the wire whereit cannotcontactsparkplug.
WHENTESTING FORENGINE SPARK
* Useapproved sparkplug tester.
* DONOTcheck f or sparkwith sparkplug removed.
Oil
OiJRecommendations
NOTE:Use a high quality detergent oil classified "For Service
SF, SG, SH, SJ" or higher. DO NOT use special additives.
1. Choosea viscosity according to the table below:
104 F _====_ _&==_ _ ' &==Z
86 _..--
68
50 o
32
14
4
-22
40 C
o 30
20
10
_ 0
-10
-20
-30
NOTE:Synthetic oil meeting ILSAC GF-2,API certification
mark and API service symbol with "SJ/CF ENERGY
CONSERVING" o r higher, is an acceptableoil at all
temperatures. Use of synthetic oil does not alter required oil
change intervals.
SAE30: 40°F and higher (5°C and higher) is good for all
purpose use above 40°F, use below 40°F will cause hard
starting.
10W-30:0 to IO0°F (-18 to 38°C) is better for varying
temperature conditions. This viscosity improves cold weather
starting, but may increase oil consumption above 80°F
(27°C).
*Check oil level frequently at higher temperatures.
Synthetic 5W-30:-20 to 120°F(-30 to 40 °C) provides the
best protection at all temperatures as well as improved
starting with less oil consumption.
5W-30: 40°F and below (5°C and below) is recommended for
winter use and works best in cold conditions.
CheckingOil Level
Oil level should be checked prior to each use or at least every
5 hours of operation. Keep oil level maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean cloth.
Replaceand tighten dipstick. Removeand and check oil
level.
3. Verify oil is at "Full" mark on dipstick. Replace and
tighten dipstick.
/p--\
@
17