Scheppach RT2300-Li18V Manual De Instrucciones Original página 16

Please note that our equipment has not been de-
signed for use in commercial, trade or industri-
al applications. Our warranty will be voided if the
equipment is used in commercial, trade or industrial
businesses or for equivalent purposes.
Remaining hazards
The machine has been built using modern technology
and in accordance with recognized safety rules.
Some hazards, however, may still remain.
• Wear regulation safety gear such as safety boots
and tight work clothing.
• Electrical hazards exist when unsuitable electric
connections are used.
• Although having regarded all considerable rules
there may still remain not obvious remaining haz-
rds.
• Minimize remaining hazards by following the in-
structions in "Safety Rules", "Use only as author-
ized" and in the entire operating manual.
Technical data
Nominal voltage
Speed n
0
Cutting circle diameter of line
Cutting line diameter
Weight (without battery)
Noise and vibration
The noise and vibration values were developed us-
ing a standardised measuring process.
Sound pressure L
pA
Sound power L
wA
Uncertainty K
WA
Vibration A
hv
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves
Before starting the equipment
Unpack the device and check it for complete delivery
contents and transport damage.
16 GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
NOTE
The batteries (optional; depending on the delivery
scope) are not fully charged on delivery. Before first
use, fully charge the batteries. See charger instruc-
tion manual.
Removing / inserting the battery(Fig. 2)
1. To remove the battery (3) from the appliance,
2. To insert the battery (3), place it on the guide
Use
Height adjustment (Fig. 3)
Undo the union nut (4) until the grass trimmer handle
can be moved in and out freely. Now set the required
working height and secure the handle in this position
by tightening the union nut again.
Adjusting the additional handle (Fig. 4)
Undo the adjustment lock for the additional handle
18 V
until it can be moved forwards and backwards without
8000 min
-1
any great resistance. Set the required position and
230 mm
tighten the securing screw again.
1,2 mm
Operation
1,85 kg
To obtain maximum performance from your grass
trimmer, please follow these instructions:
• Never use the grass trimmer without the guard.
• Do not mow grass when it is wet. The best results
72,4 dB(A)
• Do not allow the grass trimmer near the grass un-
87,4 dB(A)
3 dB(A)
1,45 m/s² • To cut properly, swing the machine sideways while
1,5 m/s²
• If the grass is long, the grass must be cut shorter
• Use the guard hood to prevent unnecessary wear.
• To avoid unnecessary wear, keep the grass trim-
Turning on/off (Fig. 1)
• In order to turn your lawn trimmer on, press the
• Always have one hand on the auxiliary handle (12).
• In order to turn the lawn trimmer off, release the
Using the grass trimmer as an edge trimmer
(Fig. 5/6)
To cut the edges of lawns and flower beds, the grass
trimmer can be converted as follows:
• Remove the battery pack
• Fold the edge guide (9) upwards.
press the release button (13) on the battery and
pull out the battery.
track and push it back into the appliance. It will
audibly snap in.
are achieved with dry grass.
til the switch is pressed, i.e. the grass trimmer is
in operation.
moving forwards. Keep the grass trimmer inclined
at an angle of approx. 30° while you do so .
in stages, starting from the tip.
mer away from hard objects.
dead man switch (1) and the on/off switch (2
on/off switch (2).