Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS ON ASSEMBLY AND USE
GB
CONGRATULATIONS ON PURCHASING YOUR PRODUCT!
Please read these instructions carefully. The instructions are an integral part of the
product. Therefore, please store them and the packaging carefully in case questions
arise in the future. Please always include these instructions when you are handing
on the product to a third-party. Children should only assemble, use or repair the
product when they are under adult supervision. This product is not suitable for indus-
trial use.
TECHNICAL SPECIFICATIONS:
Item: Choppa Street Monster
Item number: 10030
Maximum carrying capacity: 60 kg
Dimensions when assembled: 100 x 54 x 74 cm
If you have assembly problems or would like further information on the product, we
have all you need and more at http://www.hudora.de.
COMPONENTS:
1. Front wheel and fork with pre-assembled foot pedal
2. Pedals
3. Fork head with screws
4. End cap
5. Handlebars with pre-assembled hand brake
6. Steering plate with 4 screws
7. Front frame
8. Rear frame with 2 attachment screws
9. Front seat part with attachment screws
10. Rear seat part with supporting tube
11.Rear wheels with axle screws, nuts and washers
12.Set of tools
A. Brake lever
A1. Lock nut
A2. Adjusting screw
B. Screw
C. Cap nut
D. Brake arm
E. Brake shoes
F. Allen screws
G. Spring adjusting screw
ASSEMBLY:
1. Take all the components from the carton and check these for completeness.
(Fig. 1)
2. Connect the front frame (7) to the back frame (8) by inserting the sections of the
frame together. You can vary the length of the frame by using the front or rear
2 bore holes. Secure the sections of the frame with screws, washers and nuts.
Take care to ensure that you always use 2 screws to secure the frames. (Fig. 2)
3. The back wheels (11) are supplied with pre-assembled bolts, nuts and spacer
washers. Screw the axle bolts into the axle, as shown in Fig. 1. Use the Allen key
for this.
CAUTION: Do not tighten bolts too tightly!!! Nuts must not rub against
each other otherwise the wheels will be blocked!
4. Mount the front wheel fork (1) to the frame as shown in Fig. 3.
5. Place the end cap (4) on top, insert the washers and screws and tighten well.
6. Place the handlebars (5) on the end caps (4) (Fig. 5). When attaching the steering
plate on top, make sure that it is positioned right in the middle of the handlebars
and that all screws are well tightened so that the handlebars cannot shift. Evenly
tighten the screws crosswise.
7. The seat is made up of the front and rear parts (9, 10) of the seat and the
supporting tube. Join the two seat parts and mount the seat bucket to the frame
with the aid of the screws and nuts. Make sure that the screws are inserted
through the holes in the seat, the supporting tube and the frame. Now tighten the
screws. The seat is adjustable horizontally. Please set up the seat according to
your child's height (Fig. 6).
8. Screw the pedals (2) onto the cranks (Fig. 7). Ensure that the pedals are screwed
on securely.
HUDORA GmbH
Jägerwald 13
42897 Remscheid
GERMANY
http//:www.hudora.de
9. Adjusting the brakes (Illus. 8 and 9):
Before adjusting the brakes, check with your child whether he or she can
operate the brake lever (A) without any problem. By turning the screw (B), you
can reduce the distance between the brake handle and the handlebar and
adjust it to suit the size of your child's hand. The initial adjustment can be made
to the brake lever (A). If it is not enough, you will be required to retighten the
cable winch. Loosen the counter nut (A1) and unscrew the locking screw (A2)
from the brake lever and fasten the counter nut again. For adjusting the brakes,
loosen the cap nut (C) on the brake arm (D) which keeps the cable winch in place.
When you now press the two brake arms towards the rim with hands, the
distance between the brake shoe and rim should be at least 1 mm and maximum
3 mm. Fasten the cable winch by screwing in the cap nut. Check the brake shoes
seating (E). The entire surface must be pressed on to the rim when the brake is
pressed. If the brake shoes are not positioned on the edge of the rim, you will
need to readjust them by releasing Allen screws (F). Make sure you fasten them
properly after the adjustment. If now a brake arm pulls more or less, correct the
fault through spring setting screw (G) directly on the brake arms. If a brake arm
does not get pushed in adequately on the rim, you will be required to turn the
spring setting screw (G) further inwards. If it presses more than required into the
rim, pull out the spring setting screw a little. Before the fi rst ride, apply the brakes
several times to ensure that all screws have been fastened properly and the brake
works without any problems
Before any use, ensure that all parts are securely connected with each other. For
your own safety, you should replace damaged parts immediately. It is recommended
to employ original parts in any replacement or to be advised concerning this by a
specialist. Right to technical changes reserved.
CAUTION:
• Not suitable for children under 3 years of age. The Choppa should always be used
under the supervision of adults. It is not suitable for use on public roads and
should not be used in darkness.
• Keep small parts away from small children. Risk of suffocation.
• Please wear a safety helmet.
• Corresponds to EN-71
In case of any questions, our Service Center remains available to you.
CARE AND MAINTENANCE:
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Store the product in a safe place where it is protected from the elements,
cannot be damaged, and cannot injure anyone.
For your own safety, please use original spare parts only. These can be sourced from
HUDORA. Do not make any structural changes.
If parts become damaged or if sharp edges or corners should develop, the product
may not be used any more. If in any doubt, please contact our service team
(http://www.hudora.de).
DISPOSAL ADVICE:
At the end of the product's life, please dispose of it at an appropriate collection point
provided in your area. Local waste management companies will be able to answer
your questions on this.
SERVICE:
We make every effort to deliver faultless products. If faults do arise however, we put
just as much effort into rectifying them.
Therefore, you can fi nd numerous information on the product, replacement parts,
solutions to problems and lost assembly manuals at http://www.hudora.de.
Item no. 10030
As of 11/09
Page 4/7
Publicidad
