Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame
Bumper
rail
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75528F
Wrenches: 18mm
Drill Bits: None
Exhaust not shown.
Sandwich spacer between
receiver and bumper
Lower exhaust system for ease of installation.
1
Qty. (6)
Hex Bolt M12X1.75X45 CL10.9
2
Qty. (6)
Conical Washer
1.
Remove the fascia door. Return to owner.
2.
Detach the rubber exhaust hangers and lower the rearward portion of the exhaust ((2) on single exhaust, (4) on
dual).
3.
Raise hitch into position over the exhaust pipes aligning the slots in the hitch with the weldnuts in the bottom of the
frame rails.
4.
Loosely install the M12 bolts and conical washers.
5.
Install M12 bolts & conical washers through receiver at the bumper attachment. Sandwiching the spacer between
the receiver and bumper and into the weldnuts in vehicles bumper.
6.
Loosely attach fasteners as shown, center hitch on vehicle and tighten fasteners to 92 Lb.-Ft. (125 N*M).
7.
Raise exhaust system back into position.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2007 Cequent Towing Products
Installation Instructions
Fascia
Spacer
Bumper
.
Tighten all M12 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
GMC Acadia
Saturn Outlook
Buick Enclave
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV 1 , SUV2
Fasteners Typical Both Sides of Vehicle
Existing
weldnuts
3
2
1
3
Qty. (2)
Spacer
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5000 (2270 Kg)
5000 (2270 Kg)
Frame rail
2
1
75528N
5-11-07
Form: F205 Rev A 5-6-05
75528
87435
44569
Max Tongue
WT (LB)
500 (227 Kg)
500 (227 Kg)
Rev. B
Publicidad
Manuales relacionados para Cequent Towing Products 75528
Resumen de contenidos para Cequent Towing Products 75528
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75528N 5-11-07 Rev. B 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 75528N 5-11-07 Rev. B 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 75528N 5-11-07 Rev. B 2007 Cequent Towing Products Form: F205 Rev A 5-6-05...