Asist AE9CPK90 Instrucciones De Uso página 40

The motor is protected by a thermal fuse against
overheating. If the motor is to start, the pump switch-
es off automatically. After cooling down, the pump
switches on again automatically (approx. 19 minutes).
Location and transport
- Make sure that the pump is placed on a solid base
(especially during automatic operation)
- Make sure that the pump is positioned so that the
openings on the suction base are not completely or
partially blocked. Therefore, it is advisable to place
the pump on two bricks.
- Do not use the power supply or float cable to hang
or carry the pump.
- If it is necessary to hang the pump, use a rope
attached to the handle.
CLEANING AND MAINTENANCE
- Always unplug the pump when cleaning, repairing
and maintaining the pump.
Before each use
Check the cover, cable and plug for damage. - Visual
inspection.
Check that the float switch is not damaged.-Lift and
shake the switch to check the free movement of the
contained metal balls.
Cleaning the device from the outside
Rinse with clean water. Remove solid debris with
brush and detergent. Immerse the pump in a tank of
clean water and switch it on for a short time to flush
the inside of the pump.
Suction area cleaning
Clean all accessible internal parts of the cover. Re-
move dirt around the rotor head by opening the pres-
sure connection. Remove solid debris with brush and
detergent.
WARNING! Before using the pump again, let it „soak"
so that any possible residual dirt does not block the
device.
Storage
The device must be stored in a warm place protected
from frost.
WARNING - risk of equipment damage! Frost de-
stroys equipment and accessories because they
always contain water.
Storage when not used for a long time
Do not store the pump in a place where the tempera-
ture is high.
If possible, store the pump in a place with a constant
temperature and humidity.
Possible defects
The following problems may occur during operation:
Faults Causes Remedy
40
No power
Pump does Float switch does
not start not turn on Check
power
The water level
is below the
The pump minimum pumping
works but level
does not Clogged inlet filter.
suck water Clogged outlet
tube.
Squeezed hose
The input strainer
is blocked
Insufficient Insufficient pump
performanc performance due
to heavy soiling
and corrosion
Motor protection
disconnects
the pump, Very
The pump
strong water
switches off
contamination
after a short
Water
period of
temperature too
operation
high, protection
switches off the
motor
AE9CPK90 SPECIFICATIONS
Input voltage 230 V
Input frequency 50 Hz
Power consumption 900W
Max. pumping capacity 17000 l / h
Max. discharge height 9 m
Max. liquid temperature 35 oC
Max. particle size 35 mm
Max. immersion depth 7 m
Weight
Protection class I.
outlet hose diameter: 38mm, 50mm (1 - 6/4)
Degree of protection IP IPX8
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
Check the power
supply
move the activated
float switch to a
higher position
Immerse the
pump deeper (as
possible).
Clean the filter.
Clean the tube
and switch the pump
on again
Clean the pump and
replace worn parts
Disconnect the
pump from the el.
Clean the pump and
base
Observe a maximum
temperature of
35 ° C
3,3 kg