Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
The blue LEDs (4) will illuminate in segments, displaying
u
the state of charge in the battery.
The completion of charge is indicated by the blue LEDs
u
(4) will turn off. The pack is fully charged and may be used
at this time or left on the charger.
Assembly (Fig. D)
Align the top of the extension tube (8) with the vacuum
u
inlet (6) as shown in figure D.
Push the extension tube (8) onto the vacuum inlet (6) so it
u
locks into position.
Align the bottom of the extension tube (8) with the
u
floorhead (12) as shown in figure D.
Push the bottom of the extension tube (8) onto the
u
floorhead (12) so it locks into position.
To remove the tube, press the extension pole release
u
button (9) located on the vacuum inlet or the bottom of the
extension tube and gently pull the connected accessory
off.
Using an accessory tool (Fig. E)
Your vacuum may come with some of the following tools.
1. 2-in-1 brush (13)
2. Crevice tool (14)
3. Pet head (Only available with BHFEA640WP unit) (15)
4. Powered pet head (Only available with BHFEA640WP
unit) (16)
The accessories 13, 14, 15 and 16 can be fitted either
u
directly to the extension tube (8) or to the vacuum inlet (6)
as shown in figure E.
Align the top of the accessories 13, 14, 15 and 16 with the
u
vacuum inlet (6) or extension tube (8) and push into place
so it locks into position as shown in figure E.
Use (Fig. E1)
This vacuum can be used in one of four ways.
1. With the extension tube (8) and the floorhead (12).
2. With the floorhead (12).
3. With the extension tube (8) and an accesssory tool
4. With an accesssory tool.
Switching ON and OFF (Fig. F)
To switch ON, push the ON/OFF button (1) .
u
To change speed setting press hard floor mode (2) or
u
carpet mode (3) depending on floor type.
Note: The state of charge indicator LEDs will illuminate
while the vacuum is ON.
To switch OFF, press the ON/OFF button (1) a second
u
time.
Return the product to the charger immediately after use so
u
that it will be fully charged and ready for the next use.
Note: Ensure that the product is fully contacting the magnetic
charger plug.
10
(Original instructions)
Accessory storage on pole
Accessory (13, 14, 15) can be stored on the pole of the
u
unit using the on pole storage attachment (20).
Align the pole storage clip feature (20) onto the rear of the
u
pole.
Push firmly so that the pole storage is held firmly on
u
position on the pole.
The accessories (13, 14, 15) can be fitted directly to the
u
on pole storage attachment.
Align the top of the accessories (13, 14, 15) with the pole
u
storage attachment (20) and push into place so it locks.
Note: A maximum of two accessories can be stored on the
pole storage.
Accessory storage on charge dock
The accessories 13, 14, 15 and 16) can be fitted directly
u
to the wall hanging charge dock (18) as shown in Fig. C.
Align the top of the accessories (13, 14, 15 and 16) with
u
the wall hanging charge dock arms (18b) and push into
place so it locks into position as shown in Fig. C.
Note: The storage side arms (18b) can be removed from the
wall hook. This is possible for the user to do if they don't have
enough space or only want to utilize one side arm.
To remove storage side arms from the charge dock, pull the
arm firmly upwards. To reconnect, align the arm with the
locking holes and press down.
Cleaning and emptying the vacuum
Warning! Projectile/Respiratory Hazard: never use the vac
without its filter.
IMPORTANT: Maximum dust collection will only be obtained
with clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is switched
off, this indicates that the dust canister is full and requires
emptying.
Note: There is a MAX line on the dust cannister. Do not allow
the dust cannister to fill beyond this point.
Note: The foam/felt filter (23) is re‑usable do not throw it away
when the product is emptied. We recommend that you replace
the filters every 6–9 months depending on frequency of use.
Note: Replacement filters can be purchased from your
BLACK+DECKER Service Centre. Visit www.2helpu.com to
locate a service centre.
To empty the dust canister (Fig. G, H, I)
Press button (11a) to release the dust canister (11) from
u
the chassis as shown in figure G.
Place the dust canister over a trash can and press the
u
dust canistor door release button (11b) to empty the dust
canister as shown in figure I.
Empty the contents of the dust canister (11) .
u
Close the dust canister door (11c), until it clicks firmly
u
into position.
Publicidad
