YATO YG-03087 Manual De Instrucciones página 11

out through the unloading door. After all the vegetables have been unloaded, stop the appliance by releasing the switches marked
"START" and "OUT". The operation time of the emptied peeler should be minimised.
Caution! It is not allowed to unload the products with hands or any other objects. All vegetables must fall out of the peeler under
centrifugal force.
Product Maintenance
Caution! Every time before cleaning, switch off the peeler, unplug the power cord plug from the socket, wait for the appliance to
cool down, and then proceed with maintenance.
Caution! Due to its intended use which is food preparation, the product should be maintained carefully. This will help to maintain
proper hygiene. The maintenance of the product should be carried out after each use.
Use only mild kitchen cleaning agents to clean it. It is forbidden to use abrasive cleaning agents, e.g. cleaning powder or milk, or
agents containing corrosive substances. Do not use any solvents, petrol, or alcohol to clean the product.
Dilute the cleaning agent with water, according to the instructions supplied with it. Then, apply it on a soft cloth and clean the
outside of the product and inside of the disc chamber.
Remove any residues of the cleaning agent with a soft cloth slightly soaked in clean water. Then, dry all surfaces with a dry, soft
cloth.
Caution! The product is not designed for water jet cleaning. Never immerse the product in water or any other liquid.
Pay special attention when cleaning the screen and the abrasive disc in the peeler chamber. They should be cleaned with a with
water jet of pressure not greater than that of the tap water. A plastic brush can be used to thoroughly clean the holes in the screen
and the disc. Do not use metal or sharp instruments for these components.
Caution! When cleaning the inside of the peeler with a water jet, ensure that the water runs off in the same way as during normal
operation of the product.
The screen and the abrasive disc can be removed for cleaning. Should any deformation or damage during operation be observed,
the screen and/or abrasive disc should be replaced with a new one that is free of defects. The sanding paper underneath the
screen needs to be replaced if it is worn. Replacement should be carried out at a service centre.
The remaining parts of the product may only be cleaned with a cloth soaked in a cleaning agent.
No part of the product is suitable for cleaning in dishwashers or under high-pressure water jets.
After maintenance, all parts of the product should be thoroughly dried.
Transport and storage
If the product is not to be used for a longer period of time, turn off the peeler and unplug the power cord plug from the socket.
Thoroughly clean the appliance. Leave the disc chamber cover open to thoroughly dry the inside of the disc chamber. After drying,
close the cover and secure it with a lock.
If stored, keep the product indoors, and make sure it is not exposed to dust, dirt, or moisture. It is recommended to store the
product in its original packaging.
Store and transport the product in the working position. Do not tilt or place the products in layers. Do not place anything on the
product.
SPECIFICATION
Parameter
Catalogue No.
Rated voltage
Rated frequency
Rated power
Protection class
Ingress protection rating
Water inlet pressure
Water inlet diameter
Water outlet size
Operating mode
Rated capacity
Capacity
Screen hole diameter
Net weight
Noise level:
- pressure (idle running)
- power (idle running)
O R I G I N A L
GB
Units
[V~]
[Hz]
[W]
[kPa]
[mm]
5 min ON / 5 min OFF
[kg]
[kg/h]
[mm]
[kg]
[dB(A)]
[dB(A)]
I N S T R U C T I O N S
Value
YG-03087
220 – 240
50
750
I
IP34
220
18
G3/4
5 min ON / 5 min OFF
15
165
5 / 8
61
74.5 ± 2.5
< 80
YG-03090
220 – 240
50
950
I
IP34
220
18
G3/4
20
225
5 / 8
68
74.5 ± 2.5
< 80
11