Chicco RELAX & PLAY Instrucciones De Uso página 10

ELECTRICAL PART SAFETY
• The swing must be switched on and off by an adult.
• Batteries must only be replaced by an adult.
• The batteries could leak acid or explode if thrown in fire.
• Always dispose of leaking batteries immediately: they could cause
skin injuries or other personal wounds.
• Non-rechargeable batteries must not be charged.
• Do not leave the product exposed to the rain; water seepage will
damage the electronic circuit.
• Only use batteries that are equivalent to the type recommended.
• Make sure the batteries are fitted with their poles in the right direction.
• Never use new and old batteries together as this will allow the
product not to function properly.
• Remove the batteries when the swing and the console will not be
used for long periods of time.
• Always remove flat batteries from the product. Take care to dispose
of the batteries properly.
• Never short circuit the battery terminals.
• If the swing music console is left unused for long periods of time,
it is recommended the batteries be removed from the battery unit.
• Only use alkaline batteries of the same type or equivalent to the
type recommended for a correct product functioning (only use
the following batteries: AA (LR6) 1.5 V).
• The use of rechargeable batteries is not recommended as they
may reduce the toy's operability.
• Rechargeable batteries must be charged only under adult supervision.
• Rechargeable batteries must be removed from the product during
recharging.
• Remove batteries from the product before disposing of it.
• Always keep batteries and tools out of reach of children.
• The transformer supplied must be checked periodically for any
damage to the cable, the plug or the plastic cover. If any damage
is observed, the transformer should not be used and it should be
kept out of the reach of children.
• The swing must only be used with the transformer supplied.
• To replace the batteries: unscrew the battery compartment cover
using a screwdriver, remove the flat batteries from the battery unit
and insert new batteries, ensuring the batteries are fitted with their
poles in the right direction (as shown on the product). Position the
cover and screw it completely closed.
COMPONENTS:
A. Right joint
A1. Locking buttons (2x)
A2. Controls
A3. Swing plug
B. Left joint
B1. Locking buttons (2x)
C. Lower legs (2x)
D. Seat
D1. Seat arms (2x)
D2. Reclining buttons (2x)
D3. Toybar joints (2x)
D4. Safety harness
E. Toybar with pendants
E1. Holes (2x)
E2. Pendants (2x)
F. Joint fastening kit
CARE AND MAINTENANCE
FABRIC COMPOSITION
SEAT BACKREST FABRIC: Exterior: 100% polyester. Padding: 100%
polyester.
PILLOW: Exterior: 100% polyester. Padding: 100% polyester.
• This product requires periodical maintenance. The cleaning and
maintenance of the product must only be carried out by an adult.
Periodically check the swing for signs of breakage, damage or miss-
ing parts: do not use it in this case.
• Please refer to the care label for instructions on cleaning the product.
Hand wash in cold water
Do not bleach
30° C
Do not tumble dry
Do not iron
Do not dry clean
• Check that the fabric and stitching are in good condition each time
you wash it. Over-exposure to sun or heat can cause some compo-
nents to fade and become deformed. To clean the structure, wipe
the frame with a clean, damp cloth and neutral soap. Do not sub-
merge the frame in water.
FIRST ASSEMBLY
1. Stretch joint A open (Fig. 1) and install lower leg C by inserting it
into the tube on joint A (Fig. 1A). Repeat the operation for joint B.
2. Complete the installation of the legs on the back of the structure
(Fig. 2-3).
3. To assemble the seat on the structure, insert arms D1 in the desig-
nated positions on joints A and B (Fig. 4).
4. Make sure to install seat D properly so that right joint A and the
A2 commands are found on the right side of the seat as seen from
the front (fig. 4).
5. To fasten the D1 arms to joints A and B, use fastening kit F and
follow the sequence of illustrations (Fig. 5).
6. Install toybar E, positioning it in the D3 joints (Fig. 6).
7. Insert the E2 pendants in the E1 holes (Fig. 7).
The product is now ready for use.
USE
8. After placing your child in the seat, secure him or her with safety
harness D4 (Fig. 8), taking care to adjust it to the baby's body (Fig.
8A).
9. For added comfort, the seat backrest can be adjusted to two re-
clining positions by pressing the D2 reclining button and guiding
the seat to the desired position (Fig. 9).
TOYBAR
10. The swing comes with toybar E: to move it, simply push it for-
ward or rearward (Fig. 10).
BATTERY INSERTION / REPLACEMENT
11. Find the battery compartment on the side of the control, on
right joint A; unscrew the screws of the battery unit cover and
remove the cover (Fig. 11). Insert 4 AA (LR6) 1.5 V alkaline batter-
ies, making sure the batteries are fitted with their poles in the
right direction. Replace the cover and screw in the screws.
SWING ACTIVATION
12. To switch on or adjust the 5 rocking speeds, press the "+" or "–
"buttons found on panel A2 (Fig. 12).
To switch off the rocking, press the "–" button until all of the lights
on the control are completely switched off.
To switch on the tunes, press the "musical note" button. Press this
same button up to three times to turn the tune volume up. The
fourth time the button is pressed, the tune will stop.
It is possible to set a fixed amount of time for the swing to be in
use by pressing the L button and setting the desired value ( 8, 15
and 30 minutes).
To bypass the set time, press the same button L until all of the lights
are switched off.
WARNING: Heavier children reduce the number of swings in each
of the four rocking speeds. In general, the lowest setting is meant for
smaller babies, whilst the higher settings are appropriate for older
babies.
If the rocking stops, check that:
• The batteries are not flat
10