Technical Specifications - Stanley ST-52-231-E Instrucciones De Uso

NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING, OR WHILE CONNECTED
TO A POWER SOURCE.
Introduction
To get the most out of your new fan heater, please read
through these instructions and the attached safety
regulations before use. Please also save the instructions
in case you need to remind yourself of the fan heater's
functions at a later date.
- Housing of steel plate and heat-resistant lacquer
- Supplied complete with cable and plug
Thermostat Instructions
- At first turn the thermostat to "Max" and let the heater
operate with full power input. When the room
temperature reaches the required value, turn the ther-
mostat to the left until it switches off.
- The thermostat will then switch on and off automatically
to control the room temperature according to the preset
value and to keep the room temperature constant.
- When using the heater for the first time, you may notice
a slight emission of smoke. This is quite normal and it
stops after a short time. The heating element is made of
steel and was coated with a layer of protective oil
during production. The smoke is caused by the leftover
oil as it is heated.
Function Selector Dial
with two power settings
Figure 1. Fan Heater Dials

Technical Specifications

Model Voltage / Hz
220-240V~
ST-52-231-E
50Hz
220-240V~
ST-53-231-E
50Hz
220-240V~
ST-533-401-E
50Hz
ST-55-401-E 400V~50Hz
ST-59-401-E 400V~50Hz
6
Thermostat Dial
Power Settings
Rating
2 (30W(FAN),
2,000
2000W)
2 (30W(FAN),
3,000
3000W)
2 (30W(FAN),
3,300
3300W)
3 (30W(FAN),
5,000
2500W, 5000W)
3 (30W(FAN),
9,000
4500W, 9000W)
Specifications subject to change without notice
Special Safety Regulations
- Do not place the fan heater immediately under a wall
outlet.
- Do not connect the fan heater using an on/off timer or
other equipment which can automatically switch the
device on.
- The fan heater must not be placed in rooms where
flammable liquids or gases are used or stored.
- If an extension cable is used, it must be as short as
possible and must always be fully extended.
- Children should be supervised to ensure that they do
not play with the appliance. The appliance in not
intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack
of experience and knowledge. If the appliance is
damaged, do not use it any more.
- Do not place the appliance on moving vehicles or
somewhere it may easily tip over.
- Use the appliance in places with good air ventilation, do
not position it near a wall or corner.
- It is recommended that a separate circuit serving only
this appliance be provided. Keep the power cable far
enough from the hot air outlet.
- If the supply cable is damaged, it must be replaced by
the manufacturer or service agent or a similarly quali-
fied person in order to avoid a hazard. - You must not
connect other appliances to the same electrical outlet
as the fan heater.
- Do not dispose of electrical appliances as unsorted
municipal waste; use separate collection facilities.
Contact your local government for information regarding
the collection systems available. If electrical appliances
are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into
the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the
retailer is legally obligated to take back your old
appliance for disposals free of charge.
- The fan heater is not suitable for use outdoors in damp
weather, in bathrooms or in other wet or damp
environments.
Temp
continuously
adjustable 0-85°C
continuously
adjustable 0-85°C
continuously
adjustable 0-85°C
continuously
adjustable 0-40°C
continuously
adjustable 0-40°C
Electric Fan Heater
Fuse Dims
Requirement
300x300x
13A
335 mm
315x330x
13A
350 mm
360x345x
16A
445 mm
360x345x
16A
445 mm
430x410x
16A
485 mm
Weight
4.7 kg
5.8 kg
5.8 kg
8.0 kg
12.0 kg
GB