Cleaning And Maintenance - Stanley ST-52-231-E Instrucciones De Uso

NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING, OR WHILE CONNECTED
TO A POWER SOURCE.
Special Safety Regulations (cont.)
- Please note that the fan heater can become very hot
and should, therefore, be placed at a safe distance from
flammable objects such as furniture, curtains and similar
objects.
- Do not cover the fan heater.
Assembly
1. Align holes in Heater leg frame with lower inner bracket.
2. Attach lower outer bracket to lower inner bracket using
screws.
3. Align lower inner bracket with side support.
4. Attach side supports to heater using Tilt Adjustment
Knob.
5. Slide side supports into upper brackets, align holes and
insert screws to tighten.
6. Slide upper handle brackets onto front handle, align
holes and insert screws to tighten.
7. Slide rear handle into upper handle brackets, align holes
and insert screws to tighten.
Operation
- Position the fan heater so that it stands upright on a firm
surface and at a safe distance from wet environments
and flammable objects.
- Connect the fan heater to the electrical power.
- Set the thermostat dial to the maximum temperature.
- The fan heater will switch on when the function selector
dial is set to one of the three power settings.
- Once the room reaches the desired temperature, turn
the thermostat dial back until heating element turns off.
The fan will still continue to run. The thermostat is now
set at your desired temperature, and the heater will
continue to maintain a constant temperature.

Cleaning and Maintenance

- Before cleaning the appliance, disconnect it from the
outlet and let it cool down.
- The enclosure is easy to get dirty. Wipe it often with a
soft sponge. For very dirty parts, wipe with a sponge
dipped in < 50°C water and mild detergent, then dry the
Recycling
This symbol is known as the 'Crossed-out Wheelie Bin Symbol'. When this symbol is marked on a
product or battery, it means that it should not be disposed of with your general household waste.
Some chemicals contained within electrical/electronic products or batteries can be harmful to health
and the environment. Only dispose of electrical/electronic/battery items in separate collection
schemes, which cater for the recovery and recycling of materials contained within. Your co-operation
is vital to ensure the success of these schemes and for the protection of the environment.
STANLEY and
GB
are trademarks of Stanley Black & Decker, Inc or its affiliates and are used under
license by Pinnacle Products International, Inc - www.pinnacleint.com
heater enclosure with a clean cloth. Be careful not to let
the water enter the inside of the appliance
- In order to protect the enclosure, don't splash water onto
the heater, and never use a solvent like gasoline,
isoamyl acetate, toluene, etc. to clean the heater.
- Clean the coupler, dry and pack it in a plastic bag.
- When you store the heater, let it cool down first and,
keep it dry. Then cover it with a plastic bag, put it in the
packing box and store it in a dry, ventilated place.
Plug Replacement
This appliance is supplied with a BS1363 3 pin plug fitted with
a fuse. Should the fuse require replacement, it must be
replaced with a fuse (see Technical Specifications) and
approved to BS1362.
In the event the mains plug has to be removed/ replaced for
any reason, please note: IMPORTANT: The wires in the mains
lead are coloured in accordance with the following code:
Blue – Neutral
Brown – Live
Green/Yellow – Earth
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
in your plug, proceed as follows.
The blue wire must be connected to the terminal marked with
an N or coloured black. The brown wire must be connected to
the terminal marked with an L or coloured red. The green/
yellow wire must be connected to the earthing terminal which
is marked with an E or with the earth symbol .
WARNING: Never connect live or neutral wires to the earth
terminal of the plug.
NOTE: If a moulded plug is fitted and has to be removed take
great care in disposing of the plug and severed cable, it must
be destroyed to prevent engaging into a socket.
Electric Fan Heater
7