Scheppach 5901222901 Traducción Del Manual De Instrucción Original página 34

13. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer's mains connection as well as the ex-
tension cable used must also comply with these
regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely se-
lectable connection point is not allowed.
• Given unfavourable conditions in the power supply
the product can cause the voltage to fluctuate tem-
porarily.
• The product is intended solely for use at connection
points where the following prerequisites apply:
a) A continuous current-carrying capacity of the
mains of at least 100 A per phase must be given.
• As the user, you are required to ensure that the
connection point at which you wish to operate the
product meets one of the two requirements, a) or b),
mentioned above. As necessary, consult your elec-
tric power company.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the ap-
plicable VDE and DIN provisions. Only use connec-
tion cables of the same designation.
The printing of the type designation on the connection
cable is mandatory.
If the power cord of this device is damaged, it must be
replaced by a special power cord, which is available
from the manufacturer or its service department.
34 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
AC motor:
The mains voltage must be 220 - 240 V ~ .
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm .
2
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
14. Disposal and recycling
The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused
or recycled.
The equipment and its accessories are made
of various types of material, such as metal
and plastic. Defective components must be disposed
of as special waste. Ask your dealer or your local
council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must not
be disposed of together with domestic waste in
compliance with the Directive (2012/19/EU)
pertaining to waste electrical and electronic
equipment (WEEE). This product must be disposed of
at a designated collection point. This can occur, for
example, by handing it in at an authorised collecting
point for the recycling of waste electrical and electron-
ic equipment. Improper handling of waste equipment
may have negative consequences for the environ-
ment and human health due to potentially hazardous
substances that are often contained in electrical and
electronic equipment. By properly disposing of this
product, you are also contributing to the effective use
of natural resources. You can obtain information on
collection points for waste equipment from your mu-
nicipal administration, public waste disposal authority,
an authorised body for the disposal of waste electrical
and electronic equipment or your waste disposal com-
pany.