Publicidad
Idiomas disponibles
Idiomas disponibles
EN
What is included in the box
Supply of this TV includes following parts:
•
1x TV
•
1x Remote control
•
2x AAA batteries
•
1x mini component adapter
cable
•
1x mini SCART adapter cable
Attaching the Stand
Please follow the instructions on last page of this user manual.
Wall mounting the TV
1.
Remove the four screws that are supplied in the wall mounting holes.
2.
The wall mount can now be easily attached to the mounting holes on
the rear of the TV.
3.
Install the wall mounting bracket to the television as advised by the
bracket manufacturer.
Getting started - initial set up
1.
Using the RF cable supplied, connect the TV to the TV Aerial wall
socket.
2.
For connecting to the Internet with a wired connection connect a
Cat 5/Ethernet cable (not included) from the TV to your broadband
modem/router.
3.
Insert the batteries supplied into the Remote control.
4.
Connect the power cable to the Electrical outlet.
5.
Usually the TV is supplied with a pre-paired remote control. If the
TV does not respond to remote control commands, follow the
instructions below.
Pairing the remote control:
a) If the TV turns on automatically and the "First Time Installation"
window appears on the screen, press and hold for a few seconds blue
and yellow buttons on the Remote control. The power indicator will
blink 5 times, that would con rm the pairing of TV and remote control
is completed.
b) If the TV does not automatically turn on:
– b1) [for TV with buttons] you need to power it on by pressing of
standby key located on the TV (not the remote control).
After TV started up, press once again a standby button, then "pairing
menu" will appear.
Scroll the cursor down using the buttons CH+/CH-, to select "Pair
again", and con rm it by pressing standby button one more time.
– b2) [for TV with control stick] you need to power it on by pressing
of TV control stick on TV back cover.
Press and hold TV control stick on TV back cover until special menu
appears. Choose option "Pair Again".
Simultaneously press and hold for a few seconds blue and yellow
buttons on the Remote control. The power indicator will blink 5
times, this con rming the pairing of the TV and the remote control
completed.
Now proceed with next steps to con guring the TV.
•
1x RF cable
•
1x TV stand installation packet
•
1x User guide
•
1x mini composite adapter
cable
•
1x power cable
6.
You will be now welcomed with the First Time Installation screen.
If it does not appear, on the remote control, please press [MENU] then
8-8-8-8 and the menu will appear.
If you wish to make changes to any of the default settings, use the
scroll ▲/▼/◄/► buttons. To exit this menu at anytime, press [EXIT]
button.
7.
Please set desired settings in First Time Installation screen.
STEP 1 - Set the TV Menu language.
STEP 2 - set your country
STEP 3 - Set type of network connection. If you wish to skip this step
and connect TV to network later, please choose Skip Network Setting
STEP 4 - Select the location of TV. For home use, please select Home.
For shop demonstration mode, set Store.
STEP 5 - choose if your TV has stand, or if it is mounted on the wall. TV
will set optimal audio settings for selected option.
STEP 6 - choose input source which you want to use. If you have
connected RF cable directly to TV, choose DTV. If you have satellite
directly connected to your TV, choose DVB-S*. In case you are using
set-top-box, please pick correct input to which it is connected.
8.
If you selected in last step DTV or DVB-S2, you will be asked if you
want to tune channels. If you choose "No", you can tune channels later
from SETTINGS/CHANNEL menu. If you choose "Yes", tuning menu
will appear.
Digital TV (DTV) tuning: In DVB Antenna, please choose which type
of signal you have. Terrestrial (DVB-T) or Cable (DVB-C). Then enter
Auto tuning and set your desired settings. Again choose Auto tuning
to start tuning of channels.
Satellite (DVB-S2) tuning: Enter Auto Tuning and enter Satellite. Here
you can choose between the various satellites. Select satellite which
you wish to tune by pressing OK button on remote control. Then
return to previous menu by pressing BACK button on your remote
control and choose Auto tuning to start tuning of channels.
NOTE: To shorten tuning time of satellite channels, some countries
have preinstalled channel list for most popular satellite in that region.
If this is the case for your selected country, you will be asked if you
wish to load preinstalled channel list. If you choose "Yes", satellite
channel list will be imported to your TV within few seconds.
TIP: If you are missing channels, the reason for this is likely to be signal
strength, you should consider connecting signal booster and re-tuning the TV.
Remote control
Radio controlled remote control - No more aiming in the TV direction!
Refer to remote control picture on the second page of this user
manual.
1.
STANDBY – Switch on TV when in standby or vice versa.
2.
NETFLIX – Displays NETFLIX menu.
3.
MUTE – Mute the sound or vice versa.
4.
0 – 9 – to select a TV channel directly.
5.
YouTube – Displays YouTube application.
6.
NET+ – Displays AQUOS NET+ menu.
7.
SOURCE – To display the input/source menu.
8.
TV GUIDE – Opens the 7 Day TV Guide (Digital mode).
9.
– To return to the previous channel viewed.
10. DTV – Switch to digital TV source.
11. VOL ▲/▼ – To increase/decrease the sound level.
12. FAV – To display favourites menu.
13. INFO – Press once for now/next channel information. Press twice for
programme information about current programme.
14. CH ▲/▼ – To increase or decrease the channel being watched.
15. SUBTITLE – To switch the dialogue at the bottom of the screen (on/
o ).
16. TELETEXT – Teletext mode - To enter Teletext
17. MENU – To display OSD menu.
18. BACK – Back to previous menu.
Publicidad
