DuPont WFPF3800 Instrucciones De Instalación página 20

IM WFCH2 V40 P :WFCH1_inst 8/13/09 1:47 PM Page 20
STEP 7
-Optional Direct Connect
Test the Filter System for Proper Operation
1
Turn on the cold water shut-off valve under the sink.
2
Turn on the new Faucet for Filtered Water
from the QuickTwist ™ Filter, allow the water to run for approximately 10 minutes.
3
Check for any leaks between the System Head assembly and Filter; around all fittings; on Kitchen Faucet dapter
and on faucet/tubing connection.
If there are leaks between the System Head assembly and the QuickTwist
n
Turn off the cold water shut-off valve to the Filter System and turn on the Faucet for Filtered Water to drain the water and
release pressure.
n
Remove the QuickTwist ™ Filter and inspect the O-Rings around the nozzles on top of it. Make sure they are in place and free
from dirt and particles.
n
Turn off the Faucet for Filtered Water.
n Replace the QuickTwist ™ Filter by lifting it straight up into the System Head until the two nozzles seat into the ports and the
two extended flanges on top of the QuickTwist
counter-clockwise until it stops.
n
Turn the cold water supply valve back on and turn on the Faucet for Filtered Water.
If there are leaks around the fittings:
n
Turn off the cold water shut-off valve to the Filter System to release pressure in the System.
n While pulling the 1/4" Plastic Tubing
to make sure that the 1/4" Plastic Tubing is cut squarely and that it is not scratched. If the 1/4" Plastic Tubing is unevenly cut
or scratched, cut off 1/2" to 5/8" and re-install the Plastic Tubing (see Step 5 of Installation Instructions).
n
Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.
If there are leaks on the Kitchen Faucet dapter connection:
n
Turn off the cold water shut-off valve to the Filter System to release pressure in the System.
n
Locate the Kitchen Faucet dapter.
• If the 1/4" Plastic Tubing is leaking, follow the previous steps ("If there are leaks around the fittings").
• If the thread between the Kitchen Faucet dapter and the kitchen faucet stem is leaking, tighten more securely. If leaking
continues, disconnect the 1/4" Plastic Tubing and remove the Kitchen Faucet dapter. Wrap the Kitchen Faucet dapter
and the threaded faucet stem with plumber's tape and re-install (see Step 2 of Installation Instructions).
• If the thread between the Kitchen Faucet dapter and the cold water supply line is leaking, tighten more securely. If leaking
continues, disconnect the 1/4" Plastic Tubing and remove the Kitchen Faucet dapter. Wrap the Kitchen Faucet dapter
and the cold water supply line with plumber's tape and re-install (see Step 2 of Installation Instructions).
n
Turn the cold water shut-off valve back on and turn on the Faucet for Filtered Water.
‰ If leaks continue, turn off the water supply and call Customer Service or your local plumber.
‰ For Filter Replacement Instructions please see page 7.
WFCH2 Series
D
. In order for the Filter System to flush out any air and carbon fines (fine black powder)
™ Filter:
™ Filter are fully engaged into the System Head. Turn the QuickTwist
L
with one hand, press in on the grey collar around the inlet and/or outlet fitting. Check
H
connection;
™ Filter
19
7
KITCHEN F UCET
HOT W TER COLD W TER
V LVE V LVE
RIGID PIPE INST LL TION
KITCHEN F UCET
HOT W TER COLD W TER
V LVE V LVE
FLEXIBLE HOSE INST LL TION
F UCET FOR
FILTERED W TER
F UCET FOR
FILTERED W TER
V4.0