Midi Format - Yamaha DME8i-C Manual De Instrucciones

Referencias

4. MIDI Format

Number Format Notation
Numbers ending with "h" are in hexadecimal format, while numbers
ending with "b" are binary format.
Characters "A" through "F" in hexadecimal numbers represent decimal
values 10 through 15. Other lower-case characters (usually "n" or "x")
can represent any number.
MIDI Format Chart (Rx: receive, Tx: transmit}
Command
Control Change
(Bnh)
Channel
Message
Program Change
(Cnn)
TIMING CLOCK
(F8h)
System Real-time
Message
ACTIVE SENSING
(FEh)
System Exclusive Parameter
Message Change
4.1 Program Change (Cnh)
Receive
When the "Program Change Rx Switch" is on, Program Change
messages are received on the MIDI channel specified by the "MIDI
Rx Channel" parameter.
If the "Program Change Omni Switch" is also on, however, Pro-
gram Change messages will be received on all MIDI channels re-
gardless of the "MIDI Rx Channel" setting.
When a Program Change message is received, the scene assigned to
the received program number in the "MIDI Program Change Ta-
ble" is recalled.
The effective Bank Select, Program Change range is as follows:
Bank Select MSB: 0
Bank Select LSB: 0-7
Program Change No.: 0-127
Transmit
When the "Program Change Tx Switch" is on and a scene is
switched from DME Designer, the corresponding Program Change
number will be transmitted as specified by the "MIDI Program
Change Table" and "MIDI Tx Channel" settings.
If multiple Program Change numbers are assigned to a single scene,
the Bank Select MSB/LSB and Program Change number corre-
sponding to the lowest number will be transmitted.
Rx/Tx Function
Editing the
Rx/Tx
parameters
Rx/Tx Scene Recall
MIDI Clock
Rx
Receive
MIDI Cable
Rx
Check
Editing the
Rx/Tx
parameters
DME8i-C/DME8o-C/DME4io-C Manual de instrucciones
Bank Select MSB
Status Bnh (1101nnnnb) Control Change
Data 00h (00000000b) Control Change No. 0 (Bank
Select MSB)
Data nnh (0nnnnnnnb) Control Value (Bank Select
MSB No.)
Bank Select LSB
Status Bnh (1101nnnnb) Control Change
Data 20h (00100000b) Control Change No. 32 (Bank
Select LSB)
nnh (0nnnnnnnb) Control Value (Bank Select
LSB No.)
Program Change No.
Status Cnh (1100nnnnb) Program Change
Data nnh (0nnnnnnnb) Program Change No. (0-127)
4.2 Active Sensing (FEh)
Receive
MIDI communication will be initialized if no data is received with-
in 300 ms after reception (Running Status, etc., will be cleared).
Active Sensing
Status FEh (11111110b) Active Sensing
4.3 Control Change (Bnh)
Receive
When the "Control Change Rx Switch" is on, Control Change
messages are received on the MIDI channel specified by the "MIDI
Rx Channel" parameter.
If the "Control Change Omni Switch" is also on, however, Control
Change messages will be received on all MIDI channels regardless
of the "MIDI Rx Channel" setting.
Control Change parameter resolution is 128 regardless of the effec-
tive range of the parameter.
For finer settings use Parameter Change.
Transmit
When the "Control Change Tx Switch" is on and a parameter is ed-
ited via DME Designer, appropriate Control Change data will be
transmitted as specified by the "MIDI Control Change Table" and
"MIDI Tx Channel" settings.
Refer to "Supplementary Information 1" for cases in which multi-
ple messages are assigned to a single parameter.
Status Bnh (1011nnnnb) Control Change
Data cch (0cccccccb) Control Change No. (1-31,33-
95,102-119)
vvh (0vvvvvvvb) Control Value (0-127)
4.4 Parameter Change (F0h - F7h)
Receive
When the "Parameter Change Rx Switch" is On, Parameter
Change messages are received on the MIDI channel specified by the
"Device ID (Rx Ch)" parameter.
39