Publicidad
Idiomas disponibles
Idiomas disponibles
FR
FR
WINTERING
Remove the spark plug
BLADE
/ Clean it / check if it
ES
ES
needs to be sharpened
Remove it / Brush it /
SPARK PLUG
Plug it
PT
PT
AIR FILTER
Clean it
IT
IT
7. MAINTENANCE
7.1 CLEANING
: illustration 5.1 to 5.12
EL
EL
WARNING! DO NOT HANDLE CUTTING PARTS WITHOUT GLOVES
AS THEY ARE SHARP AND CAN BECOME HOT AFTER USE,
PL
PL
POTENTIALLY CAUSING PERSONAL INJURY.
empty the fuel tank according to the instructions in the engine manual. Ensure not to bend
RU
RU
or damage the cutter when pushing the lawnmower over obstacles. Secure the product to
prevent it from slipping or falling over, damage and injury.
components using a moist, soft cloth. Do not use strong solvents or detergents on the plastic
housing or plastic components. Certain household cleaners may cause damage, and may cause
KZ
KZ
a shock hazard.
7.2 MAINTENANCE SCHEDULE
UA
UA
WARNING ! REFUEL IN A WELL-VENTILATED AREA WITH THE
ENGINE STOPPED. PLEASE REFER TO THE ENGINE OPERATOR'S
MANUAL FOR THE MAINTENANCE OF THE ENGINE PARTS.
RO
RO
Go
Stock
EN
EN
VERIFICATION
FILTERED
CLEANING
REPLACEMENT
VERIFICATION
CLEANING
SPARK PLUG
REPLACEMENT
VERIFICATION
OIL LEVEL
FILLING
DRAIN
HOT PRODUCT
COLD PRODUCT
Remove the spark plug
Let the product cool
/ Clean it / check if it
needs to be sharpened
Remove it / Brush it /
Let the product cool
Plug it
Clean it
Clean it
Before/After each use
Every 10H
X
X
EVERY WINTERING
EVERY WINTERING
WHEN NECESSARY / CONSULT
THE TROUBLESHOOTING GUIDE
X
WHEN LEVEL IS LOW
EVERY WINTERING
242
Go
Stock
VERIFICATION
CLEANING
BLADE
REPLACEMENT or
WHEN NECESSARY / CONSULT
SHARPENING
THE TROUBLESHOOTING GUIDE
VERIFICATION
CLEANING
BLADE HOLDER
WHEN NECESSARY / CONSULT
REPLACEMENT
THE TROUBLESHOOTING GUIDE
VERIFICATION
CARTER
CLEANING
VERIFICATION
STARTER ROPE
REPLACEMENT
THE TROUBLESHOOTING GUIDE
7.3 REPLACEMENT
: illustration 6.6 to 6.12
WARNING! THE REPLACEMENT OF THE CUTTING DEVICE SHOULD
BE DONE BY AN EXPERIENCED USER! REWORK OR SHARPENING
BLADES IS NOT RECOMMENDED UNLESS IT IS DONE BY A
REPAIRSERVICE OR A SIMILARLY QUALIED SPECIALIST!
When servicing, use only identical replacement parts. Use of any other parts may create a
hazard or cause product damage. If you shall replace the cutting blade, make sure that the
following characteristics are the same: same shape, same length, same thickness, same
weight, same material.
The following part of this product may be replaced by the consumer.:
→ Blade
→ Spare parts are available at an authorized dealer or through our customer service.
Turn the mower onto its side to reveal the underside of the machine. Place a block of wood or a
stop of some kind between the blade and the edge of the deck to prevent the blade from turning
freely. Using a wrench , loosen the blade nut on the bottom of the unit . Remove the blade nut,
the washer, and the blade from the machine.
Put the new blade onto the shaft and replace the blade washer and the blade nut. Tighten the
blade nut. Torque the blade nut to 44-46 N•m. Once the blade is secure, check by hand that
everything rotates as it should.
Before/After each use
Every 10H
X
X
X
X
X
X
X
WHEN NECESSARY/ CONSULT
243
FR
FR
ES
ES
PT
PT
IT
IT
EL
EL
PL
PL
RU
RU
KZ
KZ
UA
UA
RO
RO
EN
EN
Publicidad
