Descargar Imprimir esta página

Bosch PB360S Instrucciones De Funcionamiento Y Seguridad página 8

Publicidad

Idiomas disponibles

Idiomas disponibles

Audio Settings
VOLUME
Your Jobsite Stereo has 20 selectable preset volume settings.
To adjust the VOLUME level, turn Volume/Bass/Treb Dial
clockwise or counterclockwise to desired volume level.
Equalizer
Your Jobsite Stereo has 5 selectable preset equalizer settings
and custom setting which allow you to custom select the level
of Bass and Treble tones.
Pressing Equalizer repeatedly will select through 5 equalizer
and custom settings, illuminating each setting on the LCD:
JAZZ, ROCK, POP, CLASSICAL, and CUSTOM.
To set CUSTOM Bass and Treble settings, follow the steps
below:
1. Press Equalizer repeatedly until "CUSTOM" is selected.
or, simply press the CUSTOM button once.
2. Press Custom button once and "BAS" (for BASS) along
with the bass level number will flash on the LCD display.
3. Turn
Volume/Bass/Treb
counterclockwise to desired bass level.
4. Press Custom button twice and "TRE" (for TREBLE) along
with the treble level number will flash on the LCD display.
5. Turn
Volume/Bass/Treb
counterclockwise to desired treble level.
6. Press Custom button once more to set levels to memory.
Your custom bass and treble settings are now saved, and
"TRE" and treble level number stop flashing and disappear
from the LCD display.
Note: Bass and Treble settings each have a range of 0 (min)
to 10 (max) levels.
STEREO
When a strong FM signal is received by the FM tuner, "ST" will
illuminate on the LCD display. If a weak signal is received by
the FM tuner, "ST" will not illuminate on the LCD display. To
improve the sound of a weak station, adjust the external
antenna or position your Jobsite Stereo in a different location.
Radio Function
TO SELECT BAND AND STATIONS
This tuner is operated in standard AM frequency from 530-
1710kHz and in standard FM frequency from 87.5-107.9MHz.
Follow the steps below to tune the station:
1. Press Source button repeatedly until "FM" or "AM" is
selected.
2. Turn Tune +/- Dial clockwise or counterclockwise to tune
into desired radio frequency.
3. To "Seek", press and hold
to seek down or Seek+/
with a strong signal is received.
Note: If there is no station received when the unit stops
seeking, repeat the steps mentioned above to seek for the
preferred stations.
Operating Instructions
Dial
clockwise
Dial
clockwise
/-Seek button for one second
button to seek up until a station
TO PRESET STATIONS
Up to 20 stations for FM and 10 stations for AM can be preset.
Follow the steps below to preset a station:
1. Tune in to desired radio station using Tune +/- Dial.
2. To preset desired station, press MEMORY button once.
PRESET and the preset number will flash on the display.
3. Press either the
move to the desired station preset.
4. Press Memory button again to save desired station to
desired station preset to memory. PRESET and the station
preset number will stop flashing.
Note: Once 20 stations for FM or 10 stations for AM are set,
the first preset station will be replaced if you continue to preset
another station.
TO RETRIEVE PRESET STATIONS
1. Press the
/-Seek or Seek+/
down or up for the desired preset station.
AUX Function
or
If you want to use an external audio player such as a digital
media player or portable CD player, the unit has two Auxiliary
Ports to accept these sources.
AUX 1 intended for use when it is more desirable to control the
or
external player from outside the unit.
1. Press Source button repeatedly until AUX 1 is illuminated
on the LCD display.
2. Open AUX 1 IN port cover on the left side of the unit.
3. Insert plug from your cord into the AUX 1 IN jack.
4. Connect the other end of the cord into the headphone out
or Aux out port on your external audio player.
5. Play the external audio source as you normally would.
6. Use the Volume/Bass/Treb Dial to adjust the volume.
AUX 2 intended for use when it is more desirable to secure the
external player inside the Digital Media Bay (See Digital Media
Bay) for increased convenience and protection.
1. Press Source button repeatedly until AUX 2 is illuminated
on the LCD display.
2. Open Digital Media Bay Door.
3. Insert plug from your cord into the AUX 2 IN jack.
4. Connect the other end of the cord into the headphone out
or Aux out port on your external audio source.
5. Play the external audio source as you normally would.
6. Use the Volume/Bass/Treb Dial to adjust the volume.
Note: You can not control your digital media player device
(play, pause, track, etc.) through the control panel on the front
of your Jobsite Stereo when your device is connected through
an Auxiliary port.
8
/-Seek or Seek+/
buttons once to
buttons once to search

Publicidad

loading

Este manual también es adecuado para:

Pb360s-c