Publicidad
Idiomas disponibles
Idiomas disponibles
Main Menu
Sub - Menu
Hotkey1 Setting
OSD Settings
Hotkey2 Setting
Hotkey3 Setting
Input Signal
Volume
Mute
Auto Power
Eyeshield Remind
Light Sensor
Gravity Sensor
Other Settings
USB Switch
USB Power(Sleep)
USB Upgrade
Reset
Information
Troubleshooting
Symptom
Solution
The power
•
Verify that the mains power cord is securely attached to the power adapter,
button does not
is connected to a power outlet and the power outlet is switched on.
light up when
•
Verify that the power adapter is securely connected to the rear of the
pressed
monitor.
The power
•
Disconnect the power adapter from the Monitor and reconnect in 2-3
button lights up,
minutes.
but nothing is
•
Press and hold the power button for 5 seconds to reset the monitor
displayed on the
settings.
screen
•
Contact ALOGIC Support if the points above do not work.
Monitor does
•
Check that an appropriate video cable is connected between the computer
not show HDMI
and display and the correct input is selected on the monitor.
or DisplayPort
•
Check your computer's settings to verify that it is detecting the monitor and
video from the
is outputting video to it.
computer
•
Verify that you are using the USB-C cable that came with the monitor.
Monitor does
•
Check your computer's settings to verify that it is detecting the monitor and
not show USB-C
is outputting video to it.
video from the
•
Check that the USB-C port on your computer that the monitor is connected
computer
to supports video output using DisplayPort Alternate Mode (DP Alt. Mode).
•
Verify that the USB-C port on your computer supports charging using the
Laptop computer
USB Power Delivery (USB-PD) standard.
does not charge
•
A very small portion of laptops require more than 90W power to charge.
when connected
These tend to be high end graphics and gaming focused computers.
to the monitor
•
If necessary, connect the power adapter that came with the computer to
using USB-C
your laptop in addition to the USB-C cable that is connected to the monitor.
The terms HDMl and HDMl High-Definition Multimedia lnterface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the
United States and other countries.
Options
Brightness, Contrast, Volume, Mute,
Shadow Balance, Contextual Model,
PIP/PBP Mode, Input Signal,
Dynamic Brightness, HDR, USB switch
Light Sensor, Gravity Sensor,
Auto, Type-C, DP, HDMI1, HDMI2
0-100
Off, On
Off, On
Off, On
Off, On
Off, On
Type-B, Type-C
Off, On
No, Yes
No, Yes
Input Source, Resolution, Mode, HDR Ver, SN
Warnings
•
Only use the monitor indoors in dry locations. Do not use the monitor in damp
places or near water sources such as in bathrooms and kitchens.
•
Store and use in a cool, dry, ventilated place. Do not place close to heat
sources or in direct sunlight.
•
Ensure that the equipment is installed on a flat, stable surface. If placed on
an uneven or unsteady surface the monitor may fall and be damaged, cause
personal injury or damage other items.
•
It is normal for the device to be slightly warm to touch during operation.
Provide adequate ventilation and do not cover the device while in operation.
•
Do not cover or block the ventilation holes on the rear cover of the monitor.
Do not use on a bed, sofa, blanket or similar where the monitor may fall over
or become covered.
•
The acceptable electrical supply voltage and frequency ranges are indicated
on the label on the rear cover of the monitor. Do not connect the monitor to
power sources which fall outside these limits.
•
If the device will not be used for weeks or months, it is recommended that
the power be disconnected to save energy and protect the equipment from
damage caused by lightning strike induced power surges if a thunderstorm
occurs.
•
Do not insert foreign objects into the ventilation holes in the cover of the
monitor as damage, fire or electric shock could occur.
•
The monitor contains no user serviceable parts. Disassembling or attempting
to repair this product yourself will void the warranty and expose you to the
risk of electric shock. If you suspect a fault with the device, please contact
the seller you purchased the product from or ALOGIC after sales support for
assistance.
•
Do not use the product if it becomes damaged as this could pose a risk of
causing damage to connected devices and expose you to electric shock.
•
Do not crush, cut, pull or twist the mains power cord excessively. If the power
cord becomes damaged do not use the product until a replacement power cord
can be obtained. Using a damaged power cord may result in electric shock.
•
Do not spray liquids on the monitor. Do not use chemicals such as solvents on
the surface of the monitor. Clean the monitor only by wiping with a clean, dry,
soft, scratch-avoiding microfibre cloth.
•
Disassembling or failing to properly use and care for your device will void the
warranty on the product.
•
ALOGIC bears no responsibility for damage to the device or incidental
damages arising from improper use or lack of care and is not liable for repair/
replacement of the device or other damages in these circumstances.
Description
Choose function associated with the hotkeys
Switch display signal input
Adjust audio volume
Turn mute mode on/off
Turn auto power mode on/off
Turn eyeshield remind mode on/off
Switch between Type-C and Type-B
function modes
Turn USB power (sleep) on/off
Initiates firmware upgrades from USB flash
drive
Resets the monitor configuration
Displays monitor information
EN
11
Publicidad
