Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation instructions for part 99-7617HG
Nissan Altima
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted high gloss gray
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: • 40-NI12
Steering wheel control interface: • ASWC-1 (sold separately)
METRA - The World's best kits
®
2013-2015
(Sedan)
99-7617GHG
C
®
D
metraonline.com
Table of Contents
Dash Disassembly ................................................. 2
Kit Assembly
– ISO DIN radio provision with pocket ....................... 3
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
Publicidad
Manuales relacionados para Metra 99-7617HG
Resumen de contenidos para Metra 99-7617HG
- Página 1 ® Installation instructions for part 99-7617HG Nissan Altima 2013-2015 Table of Contents (Sedan) 99-7617GHG Dash Disassembly ..........2 Kit Assembly – ISO DIN radio provision with pocket ....... 3 KIT FEATURES • ISO DIN radio provision with pocket • Painted high gloss gray TOOLS REQUIRED •...
- Página 2 ® 99-7617HG Dash Disassembly 1. Unclip the right side of the driver’s 5. Remove the climate control panel. knee bolster panel next to the (Figure D) center console and let hang. 6. Remove the a/c vent panel. (Figure A) (Figure E) Note: There is no need to 7.
- Página 3 (Figure C) 5. Locate the factory wiring harness and antenna connector in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS. 6. Reassemble the dash in reverse order of disassembly.
- Página 4 ® Installation instructions for part 99-7617HG IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
- Página 5 ® Instrucciones de instalación para la pieza 99-7617HG Nissan Altima 2013-2015 Indice (Sedan) 99-7617GHG Desmontaje del tablero ......... 2 Ensamble del kit – Provisión de radio ISO DIN con cavidad ....3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DIN con cavidad •...
- Página 6 ® 99-7617HG Desmontaje del tablero 1. Desenganche el lado derecho del 5. Quite el panel del control del clima. panel protector de rodillas del (Figura D) conductor junto a la consola central 6. Retire el panel de ventilación de y déjelo colgando. (Figura A) aire.
- Página 7 (Figura C) 5. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. 6. Vuelva a armar el tablero al revés de...
- Página 8 ® Instrucciones de instalación para la pieza 99-7617HG IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...