Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation instructions for part 99-7628BHG
Nissan Murano 2015-up
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted to match factory finish
KIT COMPONENTS
• A) Radio housing trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8" Phillips screws
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7552
Antenna Adapter: • 40-NI12
METRA. The World's best kits.
99-7628BHG
C
®
D
metraonline.com
U.S. PATENT # D788,765
Table of Contents
Dash Disassembly ................................................. 2
Kit Assembly
– ISO DIN radio provision with pocket ...................... 3
TOOLS REQUIRED
• Panel removal tool
• Phillips screwdriver
CAUTION: Metra recommends disconnecting the negative battery
terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your
local Dealership for more information. All accessories, switches,
climate controls panels, and especially air bag indicator lights
must be connected before reconnecting the battery or cycling
the ignition. Also, do not remove the factory radio with the key
in the on position, or the vehicle running. It would be best to
remove the key from the ignition and then wait a few seconds
before removing the factory radio.
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
Publicidad
Tabla de contenido
Manuales relacionados para Metra 99-7628BHG
Resumen de contenidos para Metra 99-7628BHG
- Página 1 • A) Radio housing trim panel • B) Radio brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws • Phillips screwdriver CAUTION: Metra recommends disconnecting the negative battery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information.
-
Página 2: Dash Disassembly
99-7628BHG Dash Disassembly 1. Slide down the shifter beauty ring 7. Remove (2) Phillips screws securing under the shift knob. (Figure A) the climate control assembly below the radio and then remove. (Figure F) 2. Remove the clip from the shift knob 8. -
Página 3: Kit Assembly
2. Attach the radio brackets to the radio radio and climate controls. Metra using the screws supplied with the recommends using the proper radio. (Figure A) mating adapter from Metra and/or AXXESS. -
Página 4: Important
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians METRA. The World’s best kits. metraonline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION... -
Página 5: Nissan Murano 2015 Y Mas
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7628BHG U.S. PATENT # D788,765 Indice Nissan Murano 2015 y mas 99-7628BHG Desmontaje del tablero ..........Ensamble del kit – Provisión de radio ISO DIN con cavidad ....3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DIN con cavidad •... -
Página 6: Desmontaje Del Tablero
99-7628BHG Desmontaje del tablero 1. Deslice hacia abajo el anillo decorativo 7. Quite los (2) tornillos Phillips que sujetan de la palanca de velocidades debajo de la el conjunto del control de clima debajo del perilla. (Figura A) radio y retire. (Figura F) 2. -
Página 7: Ensamble Del Kit
Metra recomienda el uso de adaptadores adecuados de 2. Una los soportes al radio usando acoplamiento de Metra y/o de los tornillos que vienen con el radio. -
Página 8: Importante
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7628BHG IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones.