SEA bleu B200 RACK Manual De Instrucciones página 8

GATE WARNINGS AND PRECAUTIONS
allowed to make whatsoever adjustment without giving notice. This doesn't oblige
BLEU by SEA can not be deemed responsible for any damage or accident caused by product breaking, being damages or
accidents due to a failure to comply with the instructions herein. The guarantee will be void and the manufacturer responsibility
will be nullified if BLEU by SEA
professional technician who will release documentation as requested by the laws in force.
bags, foam polystyrene, nails etc must be kept out of children's reach as dangers may arise
INITIAL TEST AND STARTING OF THE AUTOMATION: After having completed the necessary operations for a correct
installation of the product and after having evaluated all the risks which could arise in any installation, it is necessary to test the
automation to guarantee the maximum safety and, in particular, to guarantee that the laws in force are fully respected.
SAFETY PRECAUTIONS: All electrical work should comply with the current regulations. A 16A / 0,030 differential switch must be
used. Separate the source cables (operators, power supply) and command cables (photocells, push-buttons, etc). Be sure the
entire system is properly earth bonded. Always run cables in separate ducts to prevent interferences.
INTENDED USE: The operator has been designed to be used for the automation of sliding gates only.
SPARE PARTS: Send request for spare parts to:
SAFETY AND ENVIRONMENTAL COMPATIBILITY: Don't waste product packing materials and/or circuits.
STORAGE: Materials
MAINTENANCE AND DECOMMISION: must only be carried out by specialised and authorised personnel.
THE MANUFACTURER CAN NOT BE DEEMED RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED BY IMPROPER
USE OF THIS PRODUCT;
BLEU by SEA reserves the right to make any required modification or change to the products and/or to this manual without any
advanced notice obligation.
GENERAL NOTICE FOR THE INSTALLER AND THE END-USER
1. Read carefully these Instructions before beginning to install the product. Store these instructions for future reference
2. Don't waste product packaging materials and /or circuits.
3. This product was designed and built strictly for the use indicated. Any other use could compromise the condition and the
operation of the product or be a source of danger.
respect to the intended one.
4. The mechanical parts must be comply with: Machine Regulation 2006/42/CE and following adjustments, Low Tension
(2006/95/CE), Electromgnetic Consistency (2004/108/CE). Installation must respect Directives: EN12453 and EN12445.
5. Do not install the equipment in an explosive atmosphere.
6. BLEU by SEA is not responsible for failure to observe Good Techniques in the construction of the locking elements to
motorize, or for any deformation that may occur during use.
7. Before attempting any job on the system, cut out electrical power and disconnect the batteries. Be sure that the earthing
system is perfectly constructed, and connect it metal parts of the lock.
8. Use of the indicator-light is recommended for every system, as well as a warning sign well-fixed to the frame structure.
9. BLEU by SEA declines all liability concerning system security and efficiency, if components used are not produced by SEA
10. For maintenance, strictly use original parts BLEU by SEA
11. Do not modify in any way the components of the automated system.
12. The installer shall supply all information concerning system's manual functioning in case of emergency, and shall hand over
to the user the warnings handbook supplied with the product.
13. Do not allow children or adults to stay near the product while it is operating. The application cannot be used by children, by
people with reduced physical, mental or sensorial capacity, or by people without experience or necessary training. Keep remote
controls or other pulse generators away from children, to prevent involuntary activation of the system.
14. Transit through the leaves is allowed only when the gate is fully open.
15. The User must not attempt to repair or to take direct action on the system and must solely contact qualified BLEU by SEA
personnel or BLEU by SEA
16. The power cables maximum length between the control unit and motors should not be greater than 10 m. Use cables with 2,5
2
mm section. Use double insulation cable (cable sheath) close to the terminals, in particular for the 230V cable. Keep an
adequate distance (at least 2.5 mm in air), between low voltage (230V) cables and safety low voltage cables (SELV) or use an
appropriate sheath that provides extra insulation having a thickness of 1 mm1.
8
The points pointed by arrows are potentially dangerous. The installer must take a thorough
risk examination to prevent crushing, conveying, cutting, grappling, trapping so as to
guarantee a safe installation for people, things and animals
Country where installation has been
to your area distributor or call our help desk. These instructions are part of the device and
must be kept in a well known place. The installer shall follow the provided instructions
thoroughly.
Any initiative taken without
manufacturer from whatsoever responsibility. The installer shall provide warning notices on
not assessable further risks. BLEU by SEA in its relentless aim to improve the products, is
original spare parts are not being used.
must be properly packaged, handled with care
service centers. User can apply only the manual function of emergency.
made). As for misunderstandings that may arise refer
BLEU by SEA products must only be used to automate doors, gates and wings.
BLEU by SEA
BLEU by SEA - Teramo - ITALY -
and with appropriate vehicles
BLEU by SEA declines all liability caused by improper or different use in
(Re. Laws in force in the
explicit authorization will preserve the
BLEU by SEA to upgrade the past production.
The electrical installation shall be carried out by a
Packaging materials such as plastic
www.bleuteam.it
;
English