Publicidad
Idiomas disponibles
Idiomas disponibles
A
Ground
B
Arm
Check if the awning is level with the use of the leveling
instrument (19) on the front bar. Adjust the angle adjuster at
either end by loosening the locking nuts of the angle adjuster,
turn the jack bolt to adjust the pitch. Adjust the arm until the
front profile is level. Tighten the locking nuts again to fix the
level of awning. To adjust the inclination of the awning, adjust
the angle adjuster on both arm shoulders to achieve the desired
inclination. Fix the locking nuts when the awning is level.
5 Operation Guide
6 Awning users are not allowed to operate the product
more than 2 rounds, in that case, motor overheat protection
status will be automatically started. In that case, pressing on
the remote control cannot run the awning. Users need to
wait for about half an hour for any manipulation.
6 Pressing "stop" button on remote control when the
awning completely opened or closed.
5.1
Remote Control
Please match code with motor before using remote funcion.
Plug in the motor, the motor will react once.
•
Way 1, Press UP and DOWN simultaneously once. Then
press STOP once. Code learning is done.
•
Way 2, press learning hole once. Code learning is done.
See image 6-5
Press button
1
Up
2
Stop
3
Down
5.2
Shade travel limit adjustment
See image 6
1. Customers can adjust and set the positions of sun shade
travel limit by themselves.
2. According to motor rotating direction, down-stroke setting:
press "DOWN" button ,the awning body will be opened,
adjust the travel limit with the use of the 4mm hex wrench
: the direction of "+" is increasing the travel limit and "-" is
DE
Benutzerhandbuch
1
Symbolerklärung
Siehe Bild 1
1. Diese Bezeichnung weist darauf hin, dass dieses Produkt in
der Europäischen Union nicht zusammen mit dem Hausmüll
C
Locking nuts
D
Jack bolt
Function
Retract / close the awing
Stop opening/closing process
Extract / open the awning
to reduce the travel limit .then press :UP" button to make
the cloth cover back, adjust the travel limit with the use of
the 4mm hex wrench:the direction of "+" is increasing the
travel limit and "-" is to reduce the travel limit .
3. After setting, open and close the awning with the remote
control and check if the setting is satisfactory. If not, repeat
step 2.
5.3
Change the batteries of the remote control
1. Open the lid of the battery.
2. Get out the battery,pay attention to the direction of
installation.
3. Put in a new battery .Close the lid of the battery.
6 Maintenance and cleaning
•
Always close the awning in windy days, heavy rain and
when you are not using it.
•
Check the overall installation and all the fasteners
regularly,especially at the beginning of a new season,to
ensure the fasteners are tightened and in good conditions.
7 Technical specifications
Motor model
Rated voltage
Rated power
Rotational speed
Torque
Ingress protection class
Maximum continuous operation cycle
Working Temperature
Wind Resistance
Protection again electric shock
Remote Control
Battery operation
Transmitter channel
Remote operation range
entsorgt werden darf. Bitte beachten Sie, dass vidaXL ein
Rückgabe- und Sammelsystem zum Entsorgen dieser
Produkte zur Verfügung stellt. Dies ist kostenlos. Wenn
Elektro- und Elektronik-Altgeräte oder Batterien/Akkus
recycelt werden, werden diese Produkte nicht verbrannt
WSME50-40/13
230V~50Hz
226W
13 RPM
40Nm
IP44
2
-20°C to +80°C
Class 1
Class I
DC90
12V
433MHz
Open 200m, two
walls 30m
DE___Benutzerhandbuch |
45
Publicidad
