Publicidad
Idiomas disponibles
Idiomas disponibles
EnGLIsH
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips offers,
register your product at www.philips.com/welcome.
General description (Fig. 1)
A Hair clipping comb
B
Length setting selector
C Cutting element
D On/off slide
E
Socket for appliance plug
F
Appliance plug
G Adapter
H Cleaning brush
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
-
Make sure the adapter does not get wet.
Warning
-
Check if the voltage indicated on the adapter and on
the appliance corresponds to the local mains voltage
before you connect the appliance.
-
The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
-
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
-
Children should be supervised to ensure that they
do not play with the appliance.
Caution
-
Never immerse the appliance in water or any other
liquid, nor rinse it under the tap.
-
Do not use the appliance in the bath or in the
shower.
-
Use and store the appliance at a temperature
between 15°C and 35°C.
-
Only use the appliance in combination with the
adapter supplied.
-
If the adapter is damaged, always have it replaced
with one of the original type in order to avoid a
hazard.
-
Do not use the appliance if the cutting element or
the hair clipping comb is damaged or broken, as this
may cause injury.
-
This appliance is only intended for clipping human
scalp hair. Do not use it for any other purpose.
General
-
The adapter transforms 220-240 volts to a safe low
voltage of less than 24 volts.
-
This is appliance is not rechargeable and can only be
operated from the mains.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this user
manual, the appliance is safe to use based on scientific
evidence available today.
Using the appliance
1
Insert the appliance plug into the appliance (Fig. 2).
2
Put the adapter in the wall socket.
Clipping with hair clipping comb
Note: Make sure your hair is clean and dry. Do not use the
appliance on freshly washed hair.
1
Comb your hair with a styling comb in the
direction of hair growth. (Fig. 3)
2
Slide the hair clipping comb into the guiding
grooves of the appliance ('click') (Fig. 4).
Make sure that the arms of the comb have been properly
slid into the grooves on both sides.
3
Press the length setting selector (1) and then move
the hair clipping comb up or down (2) to set the
desired length setting (Fig. 5).
2
The corresponding hair length is visible on the side
,
of the comb.
Length settings
With the hair clipping comb attached, the appliance can
cut hair to 10 different lengths:
Hair lengths in mm
Hair lengths in inches
3
1/8
5
3/16
7
9/32
9
3/8
11
7/16
13
1/2
15
5/8
17
21/32
19
3/4
21
7/8
4
Slide the on/off slide upwards to switch on the
appliance (Fig. 6).
5
Place the hair clipping comb on the scalp and move
the appliance through the hair slowly.
Tips
-
Start clipping at the highest length setting of the
hair clipping comb and reduce the length setting
gradually.
-
Write down the length settings you have used to
create a certain hairstyle as a reminder for future
clipping sessions.
-
To clip in the most effective way, move the appliance
against the direction of hair growth.
-
Since hair grows in different directions, you need
to move the appliance in different directions as well
(upward, downward or across) (Fig. 7).
-
Make overlapping passes over the head to ensure
that the appliance catches all the hairs that need to
be cut.
-
Make sure that the flat part of the hair clipping comb
is fully in contact with the scalp to obtain an even
clipping result.
-
To achieve a good result with curly, sparse or long
hair, you can use a styling comb to guide the hair
towards the appliance.
-
Regularly remove cut hair from the hair clipping
comb. If a lot of hair has accumulated in the comb,
remove it from the appliance and blow and/or shake
the hair out of it.
Clipping without hair clipping comb
You can use the appliance without hair clipping comb
to clip your hair very close to the skin (0.8mm) or to
contour the neckline and the area around the ears.
1
To remove the hair clipping comb, press the length
setting selector (1), move the comb upwards and
then pull it off the appliance (2). (Fig. 8)
2
Comb the hair ends over the ears before you start
to contour the hairline.
3
Slide the on/off slide upwards to switch on the
appliance (Fig. 6).
4
Tilt the appliance in such a way that only one
edge of the cutting element touches the hair
ends. (Fig. 9)
5
Only cut the hair ends. The hairline has to be close
to the ear.
6
To contour the neckline and the sideburns, turn the
appliance and make downward strokes (Fig. 10).
7
Move the appliance slowly and smoothly. Follow the
natural hairline.
Cleaning
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as alcohol,
petrol or acetone to clean the appliance.
Only clean the appliance and the adapter with the
cleaning brush supplied.
Do not use any sharp objects to clean the appliance.
Clean the appliance after every use.
1
Make sure the appliance is switched off and
disconnected from the mains.
2
To remove the comb, press the length setting
selector (1), move the comb upwards and then pull
it off the appliance (2). (Fig. 8)
3
Push the middle part of the cutting unit upwards
with your thumb until it opens (Fig. 11).
4
Clean the cutting unit with the cleaning brush
supplied (Fig. 12).
5
Clean the inside of the appliance with the cleaning
brush supplied (Fig. 13).
Note: The appliance does not need any lubrication.
Replacement
The cutting unit, the adapter and the hair clipping comb
are replaceable.
Replacing the cutting unit
Replace the cutting unit if it is damaged or worn. Only
replace the cutting unit with an original Philips cutting unit.
1
Push the middle part of the cutting unit upwards
with your thumb until it opens and then pull it off
the appliance (Fig. 14).
2
Place the lug of the new cutting unit in the slot
and push the cutting unit onto the appliance
('click') (Fig. 15).
Environment
-
Do not throw away the appliance with the normal
household waste at the end of its life, but hand it in
at an official collection point for recycling. By doing
this, you help to preserve the environment (Fig. 16).
Guarantee and service
If you need service or information or if you have a
problem, please visit the Philips website at www.
philips.com or contact the Philips Consumer Care
Centre in your country (you find its phone number
in the worldwide guarantee leaflet). If there is no
Consumer Care Centre in your country, go to your
local Philips dealer.
4222.002.8083.2
Publicidad
