Publicidad
Enlaces rápidos
DECLARATION OF CONFORMITY
This product is marked
– Low voltage no. 2006/95/CE.
– Electromagnetic compatibility no. 2004/108/CE, 92/31 EEC and 93/68 EEC.
This declaration will become void in case of misuse and/or non observance though partial of manufacturer's installation
and/or operating instructions.
OPERATING LIMITS
L
Cooling Maximum conditions
Outdoor temperature :
Room temperature :
L
Cooling Minimum conditions
Outdoor temperature :
Room temperature :
L
Heating Maximum conditions
Outdoor temperature :
Room temperature :
L
Heating Minimum conditions
Outdoor temperature :
Room temperature :
Tools required for installation (not supplied)
1. Standard screwdriver
2. Phillips head screwdriver
3. Knife or wire stripper
4. Tape measure
5. Level
6. Sabre saw or key hole saw
7. Hacksaw
8. Core bits ø 5
as it satisfies Directives:
43°C D.B.
32°C D.B. / 23°C W.B.
–15°C D.B.
10°C D.B. / 6°C W.B.
24°C D.B. / 18°C W.B.
27°C D.B.
–15°C D.B.
5°C D.B.
19. Hammer
10. Drill
11. Tube cutter
12. Tube flaring tool
13. Torque wrench
14. Adjustable wrench
15. Reamer (for reburring)
16. Hex. key
37.4255.061.00
INSTALLATION INSTRUCTIONS
- Split system air conditioner -
Model Combinations
Combine indoor and outdoor units only as listed below.
The listed indoor units can be matched with outdoor units
with the same nominal cooling capacity (MTA + MPA +
KPA, SDA + CA,...).
DUAL SPLIT SYSTEM
Indoor Units
MTAF(B)IA0R5I-- x 2
MTAFIA0R5I-- x 2
KPA8FIA0R5I-- x 2
SDA8FIA0R5I-- x 2
CA8FIA0R5I-- x 2
K70N132T-- (FRAME GRILLE)
MONO SPLIT SYSTEM (WITH ADPTER)
Indoor Units
MPA9FIB0R5I-- x 1
KPA9FIB0R5I-- x 1
SDA9FIB0R5I-- x 1
DSA10FICR5I-- x 1
CA9FIB0R5I-- x 1
K70N132T-- (FRAME GRILLE)
Power Supply:
F-GAS Regulation (EC) No. 842/2006
Do not vent R410A into atmosphere: R410A is a
fluorinated greenhouse gas, covered by Kyoto Protocol,
with a Global Warming Potential (GWP) = 1975.
11/2011
EG
I
F
D
E
Outdoor Units
GR9FI50R5I--
GR9FI50R5I--
GR9FI50R5I--
GR9FI50R5I--
GR9FI50R5I--
Outdoor Units
GR9FI50R5I--
GR9FI50R5I--
GR9FI50R5I--
GR9FI50R5I--
GR9FI50R5I--
220 - 240 V ~ 50 Hz
Publicidad
Manuales relacionados para Technibel K70N132T
Resumen de contenidos para Technibel K70N132T
- Página 1 SDA8FIA0R5I-- x 2 GR9FI50R5I-- Heating Maximum conditions CA8FIA0R5I-- x 2 GR9FI50R5I-- Outdoor temperature : 24°C D.B. / 18°C W.B. K70N132T-- (FRAME GRILLE) Room temperature : 27°C D.B. Heating Minimum conditions MONO SPLIT SYSTEM (WITH ADPTER) Indoor Units Outdoor Units Outdoor temperature : –15°C D.B.
- Página 2 IMPORTANT! • Ground the unit following local electrical codes. • The Yellow/Green wire cannot be used for any connection Please read before installation different from the ground connection. • Connect all wiring tightly. Loose wiring may cause overheating This air conditioning system meets strict safety and operating at connection points and a possible fire hazard.
- Página 3 Installation site selection - Indoor unit • Select a sufficiently strong location to support the weight of the AVOID unit. • Direct sunlight. • Select a location where tubing and drain hose have the shortest • Nearby heat sources that may affect unit performance. run to the outside.
- Página 4 SDA8FIA0R5I-- x 2 GR9FI50R5I-- Condizioni Massime in Riscaldamento CA8FIA0R5I-- x 2 GR9FI50R5I-- Temperatura esterna : 24°C B.S. / 18°C B.U. K70N132T-- (FRAME GRILLE) Temperatura interna : 27°C B.S. SISTEMA MONO SPLIT (CON ADATTATORE) Condizioni Minime in Riscaldamento Unità interne Unità esterne Temperatura esterna : –15°C B.S.
- Página 5 IMPORTANTE! • Eseguire la messa a terra dell’unità secondo le norme elettriche locali. Leggere prima di iniziare l’installazione • Il conduttore giallo/verde non può essere utilizzato per collegamenti diversi dalla messa a terra. Questo sistema di condizionamento deve seguire rigidi standard •...
- Página 6 Scelta del luogo di installazione unità interna • Verificare che il piano di appoggio sia sufficientemente resistente da EVITARE sostenere il peso dell’unità. • L’esposizione diretta al sole. • Scegliere una posizione in modo che la distanza tra le due unità sia •...
- Página 7 GR9FI50R5I-- Température extérieure : 24°C B.S. / 18°C B.H. CA8FIA0R5I-- x 2 GR9FI50R5I-- Température intérieure : 27°C B.S. K70N132T-- (FRAME GRILLE) Conditions minimales en Chauffage Température extérieure : –15°C B.S. SISTEME MONO SPLIT (AVEC ADAPTATEUR) Température intérieure : 5°C B.S.
- Página 8 IMPORTANT! • Effectuez la mise à la terre de l'appareil en respectant les réglementations électriques locales. Veuillez lire ce qui suit avant de commencer • Le câble jaune/vert ne peut en aucun cas être utilisé pour toute Ce système de conditionnement de l'air répond à des normes autre connexion que celle de la mise à...
- Página 9 Choix de l'emplacement d'installation - Appareil intérieur RECHERCHEZ • Un emplacement approprié à partir duquel l'ensemble de la pièce peut être EVITEZ climatisé de manière uniforme. • L'exposition directe au soleil. • Un emplacement suffisamment solide pour supporter le poids de l'appareil. •...
- Página 10 SDA8FIA0R5I-- x 2 GR9FI50R5I-- Außentemperatur : 24°C T.K. / 18°C F.K. CA8FIA0R5I-- x 2 GR9FI50R5I-- Raumtemperatur : 27°C T.K. K70N132T-- (FRAME GRILLE) Heizbetrieb bei Minimumbedingungen Außentemperatur : –15°C T.K. SYSTEM MONO SPLIT (MIT ADAPTER) Innenraumgeräte Außengeräte Raumtemperatur : 5°C T.K.
- Página 11 WICHTIG! Verbindungen unzureichende Erdung können Bitte vor Arbeitsbeginn lesen Unfallverletzungen oder Tod verursachen. • Erden Sie das Gerät gemäß den örtlich zutreffenden Vorschriften. Diese Klimaanlage entspricht strengen Sicherheits- und • Das Gelbe/Grüne Kabel ist für die ausschließliche Verwendung Betriebsnormen. als Erdleitung. Für den Installateur oder Bediener dieser Anlage ist es wichtig, sie •...
- Página 12 Wahl des Installationsortes - Innenraumgerät • Wählen Sie eine Stelle, an der der Boden das Gewicht des Gerätes tragen VERMEIDEN SIE kann. • Wählen Sie eine Stelle, von der aus die Rohre und der • Direkte Sonneneinstrahlung. Wasserablaufschlauch den kürzesten Weg nach darußen haben. •...
- Página 13 SDA8FIA0R5I-- x 2 GR9FI50R5I-- Condiciones Máximas en Calefacción CA8FIA0R5I-- x 2 GR9FI50R5I-- Temperatura exterior : 24°C B.S. / 18°C B.H. K70N132T-- (FRAME GRILLE) Temperatura interior : 27°C B.S. Condiciones Mínimas en Calefacción SISTEMA MONO SPLIT (CON ADAPTADOR) Temperatura exterior : –15°C B.S.
- Página 14 ¡IMPORTANTE! • Realizar la puesta a tierra de la unidad siguiendo las normas eléctricas locales. Leer antes de empezar la instalación • El conductor amarillo/verde no se puede utilizar para conexiones que no sean la de tierra. Este sistema de acondicionamiento cumple medidas rígidas de •...
- Página 15 Dónde instalar la unidad interior • Controlar que el lugar de apoyo es lo suficientemente resistente como EVITAR para soportar el peso de la unidad. • La exposición directa al sol. • Elegir una posición de modo que la distancia entre las dos unidades •...
- Página 16 OUTDOOR UNIT • UNITÀ ESTERNA • UNITE EXTERIEUR • AUßENEINHEIT • UNIDAD EXTERIOR Minimum operation and maintenance area Area minima di esercizio e manutenzione. Surface minimum de fonctionnement d’entretien. Raumbedarf des Gerätes. Area mínima de funcionamiento y manutención. Provide a solid base for outdoor unit raised from the ground level. Fix unit to base using 4 anchor bolts.
- Página 17 Use insulated copper tube. Cut approximate 30-50 cm. longer than actual distance between units. min. 8 mm min. 8 mm Utilizzare del tubo in rame isolato. Tagliare con lunghezza maggiorata di 30-50 cm. oltre la distanza tra le unità. Utiliser du tube en cuivre isolé. Couper à une longueur de 30-50 cm. en plus de la distance entre les unités.
- Página 18 Tighten connections using a spanner and a torque wrench; apply specified torque (see table). Stringere le connessioni utilizzando una chiave fissa e una chiave dinamometrica; attenersi alla tabella dei valori del momento torcente. Serrer les connexions à l'aide d'une clé fixe et d'une clé dynamométrique; respecter les couples de serrage.
- Página 19 INDOOR UNIT INDOOR UNIT DUAL SPLIT INDOOR UNIT ADAPTER ADATTATORE ADAPTATEUR 3/8F - 1/2 M ADAPTER ADAPTADOR MONO SPLIT Air purging of internal unit and refrigerant tubes. Connect the vacuum pump to the outside unit as shown in the figure. Air and moisture have undesiderable effects on the refrigerant system.
- Página 20 Remove caps from service valves of both tubes. Then start vacuum pump and let it run for the time indicated in the table (vacuum 10 mm Hg abs.). Rimuovere i cappucci delle valvole di entrambi i tubi. Quindi avviare la pompa High pressure del vuoto per un tempo consigliato come da tabella (vuoto di 10 mm Hg assoluti).
- Página 21 BASIC FUNCTIONS OF THE SERVICE VALVES • FUNZIONI PRINCIPALI DELLE VALVOLE • FONCTIONS DE BASE DE VALVES DE SERVICE • FUNKTION DER ABSPERRVENTILE • PRINCIPALES FUNCIONES DE LAS VALVULAS Narrow tube service Wide tube service Action valve (2-way) valve (3-way) Valve cap CLOSED Shipping...
- Página 22 Turn the service valves stem in counterclockwise to fully open the valves. At this point vacuum pump flexible hose can be disconnected. Replace bonnet and flare nut, tighten them to 200 kg/cm with a torque wrench. Repeat what described from K to N for the second circuit. The two indoor units have to be marked has “indoor unit A”...
- Página 23 OUTDOOR/INDOOR UNIT REFRIGERANT CIRCUIT ADDRESS • INDIRIZZO CIRCUITO REFRIGERANTE UNITA’ ESTERNA/INTERNA • ADRESSE DU CIRCUIT DE REFRIGERATION UNITE EXTERIEURE/INTERIEURE • AUSSEN/ INNENEINHEIT- KÜHLROHRE ADRESSE • DIRECCION DEL CIRCUITO DE REFRIGERACIÓN UNIDAD EXTERIOR/INTERIOR ADDRESS SETTING THROUGH REMOTE CONTROLLER • IMPOSTAZIONE INDIRIZZI TRAMITE TELECOMANDO REGLAGE DES ADRESSES AVEC LA TELECOMMANDE •...
- Página 24 ADDRESS SETTING THROUGH DIP-SWITCHES • IMPOSTAZIONE INDIRIZZI TRAMITE I MICROINTERRUTTORI REGLAGE DES ADRESSES AVEC LES INTERRUPTEURS • ADRESSEN-EINSTELLUNG MIT DEN SCHALTER REGULACION DE LAS DIRECCIONES CON LOS INTERRUPTORES INDOOR UNITS PRODUCED BEFORE DECEMBER 2010 (SEE LABEL ON THE ELECTRICAL JUNCTION BOX) UNITA’...
- Página 25 REFRIGERANT CIRCUIT CHECK • CONTROLLO CIRCUITO REFRIGERANTE • CONTROLE DU CIRCUIT DE REFRIGERATION • NACHPRÜFUNG DER KÜHLROHRE • COMPROBACIÓN DEL CIRCUITO DE REFRIGERACIÓN 1. Power ON the system. 2. Set the remote controller of unit A as following (unit B must be OFF): -Mode: COOLING -Filter: ON -Set-point: 32°C...
- Página 26 SYSTEM WIRING DIAGRAM • COLLEGAMENTI ELETTRICI DEL SISTEMA • BRANCHEMENTS ELECTRIQUES DU SYSTEME • ELEKTRISCHE ANSCHLÜSSE DES SYSTEMS • CONEXIONES ELECTRICAS DEL SISTEMA DUAL SPLIT MONO SPLIT LENGTH, SIZE WIRES AND DELAYED FUSE • LUNGHEZZA, SEZIONE CAVI E FUSIBILI RITARDATI • LONGUEUR, SECTION CABLES ET FUSIBLES RETARDES •...
- Página 27 Supply power wire A: Multipolar electric wire. Size and length of the suggested electric wire are showed on table “electrical data”. The wire must be Mod. H07RN-F (according to CEI 20-19 CENELEC HD 22). Make sure the length of the conductors between the fixing point and the terminals allows the straining of the conductors L, N before that of the grounding.
- Página 28 PUMP DOWN Pump down means collecting all refrigerant gas in the system back into Das bedeutet: das Kühlmittel in die Außeneinheit ohne Gas-Verlust zurückzugewinnen. Man benutzt es, wenn das Klimagerät in eine neue the outdoor unit without losing gas. Pump down is used when the unit is Position gestellt werden muß...
- Página 29 REMOTE CONTROL UNIT/INDOOR UNIT ADDRESS • INDIRIZZO TELECOMANDO/UNITA’ INTERNA • ADRESSE TELECOMMANDE/UNITE INTERIEURE • FERNBEDIENUNG/ INNENEINHEIT ADRESSE • DIRECCION MANDO A DISTANCIA/UNIDAD INTERIOR Disconnect the power of indoor unit. ● Remove the batteries from the remote control unit. ● Set the microswitches (see table). ●...
- Página 30 REMOTE CONTROL UNIT INDOOR UNIT TELECOMANDO UNITA’ INTERNA TELECOMMANDE UNITE INTERIEURE FERNBEDIENUNG INNENEINHEIT MANDO A DISTANCIA UNIDAD INTERIOR FACTORY STATE 1=OFF 2=OFF 3=ON 4=ON SW3: 1=OFF 2=OFF 1=ON 2=OFF 3=ON 4=ON SW3: 1=ON 2=OFF 1=OFF 2=ON 3=ON 4=ON SW3: 1=OFF 2=ON 1=ON 2=ON 3=ON 4=ON SW3: 1=ON 2=ON...
- Página 31 In order to carry on a constant improvement, our products can be modified without prior notice. Per garantire un costante miglioramento dei nostri prodotti, ci riserviamo di modificarli senza preavviso. Par souci d’amélioration constante, nos produits peuvent être modifiés sans préavis. Unsere Produkte werden laufend verbessert und können Vorankündigung abgeändert Werden.