Pc-Fax; Connecting An Analog Phone (Gdp-04Ai Only); Troubleshooting - JabloCom JabloPhone Manual Del Usuario

guages you want to upload into your phone and select a
soon as the upload is finished.

PC-fax

You can use the GDP-04i as a PC-fax for sending/receiving your faxes from/to your PC.
To use the GDP-04i as a PC-fax, you have to install fax service (optional component of Microsoft Windows installati-
on). This will add FAX as printing device in the list of your printers. Open properties of FAX and select GDP-04i as a
device for sending/receiving faxes during installation of a fax feature of your operating system.
To activate automatic receiving of incoming faxes you have to set-up Fax Console (Start/All Programs/Accessories/
Communications/Fax/Fax Console).
Warning: Digital fax function may not work properly unless it is fully supported by your GSM
service provider.

Connecting an analog phone (GDP-04Ai only)

The GDP-04Ai offers you the possibility to connect a standard analog phone.
This feature allows you to operate an analog phone in a similar way as if it is connected to a standard fixed line ne-
twork (PSTN), but over a GSM network.
You can dial a number from the GDP-04Ai as well as from the analog phone. They can not be used simultaneously.
The call is executed through your GSM connection in both cases.
An incoming call rings on the GDP-04Ai as well as on the attached analog phone. The user can answer the call from
either phone.
To switch an ongoing call from the GDP-04Ai to the attached analog phone, press the "Space" key (on the character
keyboard). You will hear the ringing signal of three short beeps. You will be disconnected once the analog phone
answers the call. You may hang up now.
To switch an ongoing call from the attached analog phone to the GDP-04Ai, press the FLASH on the phone, wait for
the call to be answered on GDP-04Ai and then hang up.
Only one phone or master PBX line (home exchange unit) can be attached.
Warning: Never connect the GDP-04Ai into a wall socket of a fixed line network (PSTN).

Troubleshooting

JABLOCOM is improving the GDP-04i phone software as well as the JabloTool call management software continu-
ously. If you find an incorrect phone behavior, please check if you use the latest available firmware version within the
JabloTool (menu Tools, Update Firmware). Detail update instructions as well as the latest JabloTool version you
can find on our website - www.jablocom.com.
Problem / Error message
No SIM card
Registration to network
failed!
Function execution failed
USSD code refused by
network
Unable to process
Sending failed
Analogue line error - deac-
tivated
Error
Incorrect entry
System error
GDP-04.i.ENG.MAN.User_Manual.15.B
PPly
Solution
Your SIM card is not placed in the SIM holder correctly or the phone does not support your
SIM card type. Check if the SIM card is placed in the holder correctly or contact your GSM
service provider.
The network refused to register your SIM card into the network. Contact your service provider.
The network did not correctly perform the USSD command you sent. Check the command
syntax or contact your service provider.
The network refused the USSD command during USSD dialog. Repeat sending the command
or contact your service provider.
There is a conflict between your request and the current phone status, for example during
phonebook import from SIM. Repeat your request.
Your text message was not sent to the network correctly. Check the phone number and try
again. If the error repeats, contact your service provider.
Possible problem on the attached analogue phone. Unplug the GDP-04i power adaptor, check
your analog phone and its cable and reconnect power adaptor to the GDP-04i.
Wrong input or action was performed, for example an incorrect service code or an incorrect
SIM toolkit command. Confirm you are using correct code.
An incorrect PIN was entered. Enter a correct one.
Internal error of the phone. Switch the phone off, disconnect the internal battery for about 10
seconds and then switch the phone on again. If the error repeats, return the phone for service.
- 13 -
. The phone will automatically switch to standby mode as
EN