Publicidad
Idiomas disponibles
Idiomas disponibles
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic fields.
General
- This appliance is waterproof. It is suitable for use in the bath or shower
and for cleaning under the tap. For safety reasons, the appliance can
therefore only be used without cord.
- The supply unit is suitable for mains voltages ranging from 100 to 240
volts.
- The supply unit transforms 100-240 volts to a safe low voltage of less
than 24 volts.
Charging
Battery status indications
- When the battery is almost empty, the battery status indicator flashes
orange.
- When the appliance is charging, the battery status indicator flashes
white slowly.
- During quick charge, the battery status indicator flashes white. After
approx. 5 minutes of charging, the appliance contains enough power for
one cordless trimming session.
- When the battery is fully charged, the battery status indicator lights up
white continuously.
Note: After approx. 30 minutes, the light goes out automatically.
Charging
Charge the appliance before you use it for the first time and when the
display indicates that the battery is almost empty. When the appliance has
charged for 1 hours, it has a cordless operating time of up to 2 hours.
1
Make sure the appliance is switched off.
1
2
2 Insert the small plug into the appliance and put the supply unit in the
wall socket.
3 After charging, remove the supply unit from the wall outlet and pull the
small plug out of the appliance.
Quick charge
After approx. 5 minutes charging, the appliance contains enough power for
one cordless trimming session.
Using the appliance
Note: This appliance can only be used without cord.
Note: Switch off and clean the appliance after each use.
Detaching and attaching cutting elements
1
To detach a cutting element, push upwards against the teeth of the
cutting element and take it off the handle.
2
1
2 To attach a cutting element, insert the lug of the cutting element into the
guiding slot at the front and push the back of the cutting element onto
the appliance ('click').
Detaching the precision shaver and nose trimmer
1
Place your finger on the arrow at the back of the attachment and push it
off the handle in the direction of the arrow.
Attaching and detaching combs
1
2
1
To attach any type of guard onto a cutting element, slide the front part
of the guard onto the teeth of the cutting element. Then push down the
center of the guard with your fingers or the palm of your hand ('click').
2 To detach any type of comb from the cutting element, carefully pull its
back part off the appliance and then slide it off the cutting element.
Note: When trimming for the first time, start by using the comb with the
maximum trimming length setting to familiarize yourself with the
appliance.
Switching the appliance on and off
Press the on/off button once to turn the appliance on or off.
Attachments for use on beard
Full-size hair trimmer
Use the full-size hair trimmer without a comb to trim hair close to the skin
(to a length of 1/32in (0.5mm) or to create clean lines around your beard,
neck and sideburns.
1
To trim hair close to the skin, place the flat side of the cutting element
against your skin and make strokes against the direction of hair growth.
2 For contouring, hold the cutting element perpendicular to the skin and
move it upwards or downwards with gentle pressure.
Beard combs
Attach a beard comb to the full-size hair trimmer to trim your beard and
moustache evenly. The appliance comes with 5 beard combs. The hair
length settings are indicated on the combs. The settings correspond to the
remaining hair length after trimming.
Comb
Stubble comb
Stubble comb
Adjustable beard comb 1/8in.- 9/32in.
1
Attach the comb to the full-size hair trimmer.
= mm
2 Adjustable comb: Push the length selector to the left or right to select
the desired hair length setting.
inch
3/64in.
5/64in.
mm
1mm
2mm
3mm-7mm
Publicidad
