Levenhuk LabZZ WTT10 Guia Del Usuario página 6

Levenhuk LabZZ WTT10 Walkie Talkie and Binoculars Set
EN
Caution! Never look directly at the Sun through this device, as this may cause permanent eye damage and even blindness.
Binoculars
Interpupillary distance adjustment
Look through the binoculars' eyepieces with both eyes. To adjust the interpupillary distance, keep varying the angle between the binoculars' parts
(relative to its central axis) until the image merges into a single circle. Remember the setting for future use.
Focusing
Follow this procedure to adjust focus setting:
• Look through your binoculars at a distant object;
• Rotate the central focusing wheel until the view is focused.
Walkie-talkie
Getting started
Press the fastener (23) and pull the pocket clip (24) gently. Open the battery compartment cover and insert 4 AAA batteries according to the correct
polarity. Close the cover until it clicks. Repeat the same steps with the second device.
Using the walkie-talkie
To turn the device on, press and hold the On/Off button (6) for 3 seconds.
The volume level is controlled by the UP (4) and DOWN (7) buttons.
Both walkie-talkies must be tuned to the same channel and CTCSS tone/DCS code (if used), so that you can communicate. Press the MENU button
(11) — the channel digit will start blinking. Select one of the channels using the UP (4) and DOWN (7) buttons and press the TALK button (15) to
confirm the choice. To select the CTCSS tone/DCS code for the current channel, press the MENU button (11) twice, specify the encoding type, and
then one of the codes. To save the settings, press the TALK button (15).
To call the other person, press the CALL button (12). During the conversation, the transfer icon (TX) will be shown on the screen.
Press the TALK button (15) to send a voice message and keep it pressed while speaking. After the button is released, the device will give a short
beep tone, indicating that the device has switched to receiving mode.
To turn the backlight on, press any button except the MENU button (11) and the monitoring button (5).
To reset to the factory settings turn the device off, press the UP button (4) and turn the device on again.
Other functions
Monitoring — is used in case of an unstable signal. It disables the squelch function so that all the signals on the selected channel become audible.
Scan — checks all channels for activity, stopping at each channel where activity is detected. Press the TALK button (15) to stop on the selected
channel.
VOX — activates voice activated transmission. Using VOX and connecting a headset, you can go on the air without pressing buttons. VOX mode is
switched on/off via the MENU button (11).
Keypad lock — allows you to exclude the accidental pressing of buttons. To activate this mode, press and hold the MENU button (11) for 2
seconds.
The TALK and CALL buttons will remain active!
Squelch — turns on automatically.
Specifications
Frequency range
Channels
Radio signal radius
Squelch
VOX
Monitoring
Scan function
Power source
Transmission power
Operating temperature range
Care & maintenance
Do not use the device in potentially explosive environments or while riding a bicycle or driving a car or any other vehicle.
Consult your doctor about the safety of the device regarding any medical device you may be using.
Do not use the device near radio sources as it may cause interference.
Use a soft, damp cloth to clean the device. Do not use any ethanol- or acetone-based fluids on it.
Warranty: lifetime. For further details, please visit our web site: www.levenhuk.com/warranty
The manufacturer reserves the right to make changes to the product range and specifications without prior notice.
446MHz
8
up to 3km /1.8mi.
+
+
+
+
4 AAA batteries (for each device)
0.5W
–20... +50°C / –4... +122°F
6