TecMate Optimate2 TM420 Modo De Empleo página 5

AutomAtic mAiNteNANce chArger for 12V leAd-Acid bAtteries
from 3Ah to 96Ah, As fouNd iN:
DO NOT USE FOR NiCd, NiMH, Li-Ion OR NON-RECHARGEABLE BATTERIES.
charge rate: 0,8 Ah / hour, will recharge a 38Ah battery in 48 hours.
input: 100-240V maximum 0,23A. the maximum output current is 0,8A.
IMPORTANT: READ THE FOLLOWING INSTRUCTIONS BEFORE USING THE CHARGER
this appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety. children should be supervised to ensure that they do not play with the appliance.
sAfetY WArNiNg ANd Notes:
Disconnect AC power supply before making or breaking DC/battery connections. Battery acid is highly corrosive. Wear
protective clothing and eyewear and avoid contact. In case of accidental contact, wash immediately with soap and water.
Check that the battery posts are not loose; if so, have the battery professionally assessed. If the battery posts are corroded,
clean with a copper wire brush; if greasy or dirty clean with a rag damped in detergent. Use the charger only if the input and
output leads and connectors are in good, undamaged condition. If the input cable is damaged, it is essential to have it
replaced without delay by the manufacturer, his authorised service agent or a qualified workshop, to avoid danger. Protect
your charger from acid and acid fumes and from damp and humid conditions both during use and in storage. Damage
resulting from corrosion, oxidation or internal electrical short-circuiting is not covered by warranty. Distance the charger
from the battery during charging to avoid contamination by or exposure to acid or acidic vapours. If using it in the horizontal
orientation, place the charger on a hard, flat surface, but NOT on plastic, textile or leather. Use the fixing holes provided in
the enclosure base to attach the charger to any convenient, sound vertical surface.
eXPosure to liQuids:
the casing from above, or to light rainfall. Prolonged exposure to falling rain is inadvisable and longer service life will be
obtained by minimizing such exposure. Failure of the charger due to oxidation resulting from the eventual penetration of
liquid into the electronic components, connectors or plugs, is not covered by warranty.
bAtterY coNNectioNs:
clips for charging the battery off-vehicle, the other connection set comes with metal eyelet lugs for permanent connection to
the battery posts, and re-sealable weatherproof cap on the connector that connects to the charger output cable. This
connection set allows easy and sure connection of the charger to maintain the battery on-vehicle. The resealable
weatherproof cap is designed to protect the connector from dirt and damp whenever the charger is not attached. Consult a
professional service agent for assistance in attaching the metal eyelets to the battery posts. Secure the connector with
weatherproof cap so that it cannot foul any moving part of the vehicle or the cable can be pinched or damaged by sharp
edges. The in-line fuse in the eyelets connection set protects the battery against such accidental shorting across positive
and negative conductors. Replace any burnt fuse only with a similar new fuse of 15A rating.
coNNectiNg the chArger to the bAtterY
1. Disconnect AC power supply before making or breaking DC / battery connections.
2. If charging a battery in the vehicle with the battery clips, before making connections, first check that the battery clips
can be safely and securely positioned clear from surrounding wiring, metal tubing or the chassis. Make connections in
the following order: First connect to the battery terminal not connected to the chassis (normally positive), then connect
the other battery clip (normally negative) to the chassis well away from the battery and fuel line. Always disconnect in
reverse sequence.
3. When charging a battery out of the vehicle with the battery clips, place it in a well ventilated area. Connect the charger
to the battery: RED clamp to POSITIVE (POS, P or +) terminal and BLACK clamp to NEGATIVE (NEG, N or –) terminal.
Make sure the connections are firm and secure. Good contact is important.
4. if the battery is deeply discharged (and possibly sulphated), remove from the vehicle and inspect the battery
before connecting the charger for a recovery attempt. Visually check the battery for mechanical defects such as a
bulging or cracked casing, or signs of electrolyte leakage. If the battery has filler caps and the plates within the cells
batteries emit eXPlosiVe gAses - prevent flame or sparks near batteries.
This charger is designed to withstand exposure to liquids accidentally spilled or splashed onto
2 interchangeable connection sets are available, supplied with the charger is a set of battery
5