16. Do not block the outlet grille and rear grill .
17. After finished using, release the water from the water tank.
18. If the device is not used for long periods of time, unplug it from the network.
19. Do not move the device when the water tank is filled with water.
20. Do not place any objects on the device.
21. The devices can be used only with efficiently working ventilation.
DEVICE DESCRIPTION (fig. A)
1. Handle
3. Wheels
5. Water tank
7. Water level indicator
USING THE APPLIANCE
A noticeable reduction in the temperature of the outlet air occurs after putting into the water tank 2 plastic containers attached to the
product, previously filled with water and frozen in the freezer. It is recommended to fill the tank with cold tap water.
1. After unpacking the device from the packaging, mount the wheels and set the air cooler on a dry, flat surface, then connect the power
plug.
2. Slide out the water tank (5) on the back of the appliance and pour in the water. Be careful not to exceed the maximum level.
3. Turn on the device with the "LOW", "MID" or "HIGH" button on the control panel, thus determining the airflow rate:
"LOW" - slow fan speed
"MID" - medium fan speed
"HIGH" - fast fan speed
4. The "SWING" button causes oscillation of vertical blinds, which ensure even distribution of cooled air streams. The horizontal blinds
do not move automatically - you can move them manually.
5. The "COOLING" button reduces the temperature of the exhaust air by activating the water pump. Two ice containers (6) are included
in the set. To use ice containers placed them in the freezer for about a day first. Then insert one or both of them into the water tank (5)
without exceeding the maximum level marked on the water tank. The "COOLING" function also moisturizes the air.
6. During operation of the device, periodically check the water level for refilling the tank. Do not activate the "COOLING" function if the
water level is lower than the minimum level.
7. To end the operation of the device, press the "OFF" button on the control panel.
CLEANING AND MAINTENANCE
1. It is recommended to clean the device with a soft, dry cloth. Do not use any chemical solvents as they may permanently damage or
deform the surface.
2. After a long time of use, the mesh filter (4) and mesh filter's frame (8) will be clogged with dust, which will significantly affect the
cooling efficiency of the device. If the water does not change for a long time, mold may occur. We recommend cleaning the mesh filter
(4) and mesh filter's frame (8) once every two weeks. The cleaning procedure is as follows:
a) Disconnect the device from the power supply, open two latches on the back cover, then remove the frame and filter.
b) Wash the filter in a mild solution of detergent and warm water, then rinse with clean water.
c) Wash the mesh filter under running clean water. Use a soft brush for cleaning.
3. Pour out water from the tank before storage. Then dry the device, mesh filter, mesh filter's frame and housing to avoid moisture
damage.
TECHNICAL DATA
Supply voltage: 220-240 V ~ 50 Hz
Power: 80W
Maximum power: 350W
Capacity: 4L
Water consumption: 0.7-0.8 liters / hour
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
LESEN SIE AUFMERKSAM WICHTIGE ANWEISUNGEN BEZÜGLICH DER SICHERHEIT
DER BENUTZUNG BEWAHREN SIE DIESE FÜR DIE ZUKUNFT AUF
Bei Verwendung des Gerätes zu gewerblichen Zwecken werden die Garantiebedingungen
geändert.
1.
Vor dem ersten Gebrauch, die Bedienungsanleitung lesen und die dort angegebenen
2. Control panel
4. Mesh filter
6. 2 ice containers
8. Mesh filter frame
ALLGEMEINE SICHERHEITSVORSCHRIFTEN
Device is made in class I of insulation.
Device is compliant with EU directives:
Low voltage directive (LVD)
Electromagnetic compatibility (EMC)
Device marked CE mark on rating label
DEUTSCH
4